Replacement

DIFFERENTIAL: REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL: REPLACEMENT

REPLACEMENT

1. REMOVE REAR WHEEL
2. REMOVE NO. 2 DIFFERENTIAL SUPPORT PROTECTOR Removal

3. DRAIN DIFFERENTIAL OIL
(a) Using a hexagon wrench (10 mm), remove the differential filler plug and gasket.
(b) Using a hexagon wrench (10 mm), remove the differential drain plug and gasket, and drain the oil.
(c) Using a hexagon wrench (10 mm), install the differential drain plug and a new gasket.
Torque: 49 Nm (500 kgf-cm, 36 ft-lbf)
4. REMOVE REAR NO. 1 FLOOR PANEL BRACE Removal

5. REMOVE FRONT CENTER FLOOR BRACE Removal

6. DISCONNECT HEATED OXYGEN SENSOR (for 2WD) Removal

7. DISCONNECT HEATED OXYGEN SENSOR (for 4WD) Removal

8. REMOVE FRONT EXHAUST PIPE ASSEMBLY Removal

9. REMOVE TAIL EXHAUST PIPE ASSEMBLY Removal

10. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
2GR-FSE: Removal
4GR-FSE: Removal
11. REMOVE REAR SUSPENSION MEMBER BRACE LH






(a) Remove the 2 bolts and rear suspension member brace LH.
12. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY
(a) Remove the 3 bolts and disengage the 2 clamps and No. 3 parking brake cable assembly LH.





(b) Separate the No. 3 parking brake cable assembly LH from the parking brake equalizer.
13. SEPARATE REAR STABILIZER LINK ASSEMBLY LH Removal

14. REMOVE REAR AXLE SHAFT NUT Removal

15. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY Removal

16. SEPARATE REAR SPEED SENSOR Removal

17. SEPARATE NO. 2 REAR UPPER CONTROL ARM ASSEMBLY Removal

18. SEPARATE NO. 1 REAR UPPER CONTROL ARM ASSEMBLY Removal

19. SEPARATE NO. 1 REAR SUSPENSION ARM ASSEMBLY Removal

20. SEPARATE NO. 2 REAR SUSPENSION ARM ASSEMBLY Removal

21. SEPARATE TOE CONTROL LINK SUB-ASSEMBLY Removal

22. REMOVE REAR AXLE ASSEMBLY Removal

23. REMOVE REAR DRIVE SHAFT ASSEMBLY Removal

24. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
(a) Using SST, remove the oil seal.





SST: 09308-10010
25. INSTALL REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for 2GR-FSE)






(a) Using SST and a hammer, install a new oil seal.
SST: 09223-15030
SST: 09950-70010
09951-07200
Oil seal installation depth:
-0.5 to 0.5 mm (-0.020 to 0.020 in.)
(b) Apply MP grease to the oil seal lip.
26. INSTALL REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for 4GR-FSE 2WD)






(a) Using SST and a hammer, install a new oil seal.
SST: 09213-70011
SST: 09950-60010
09951-00410
09951-00620
09952-06010
SST: 09950-70010
09951-07100
Oil seal installation depth:
-0.5 to 0.5 mm (-0.020 to 0.020 in.)
(b) Apply MP grease to the oil seal lip.
27. INSTALL REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for 4GR-FSE 4WD)






(a) Using SST and a hammer, install a new oil seal.
SST: 09710-04101
SST: 09950-60010
09951-00580
09951-00620
09952-06010
SST: 09950-70010
09951-07100
Oil seal installation depth:
0 to 1.0 mm (0 to 0.039 in.)
(b) Apply MP grease to the oil seal lip.
28. INSTALL REAR DRIVE SHAFT ASSEMBLY Installation

29. INSTALL REAR AXLE ASSEMBLY Installation

30. INSTALL NO. 2 REAR UPPER CONTROL ARM ASSEMBLY Installation

31. TEMPORARILY TIGHTEN NO. 1 REAR UPPER CONTROL ARM ASSEMBLY Installation

32. TEMPORARILY TIGHTEN NO. 1 REAR SUSPENSION ARM ASSEMBLY Installation

33. TEMPORARILY TIGHTEN NO. 2 REAR SUSPENSION ARM ASSEMBLY Installation

34. INSTALL TOE CONTROL LINK SUB-ASSEMBLY Installation

35. INSTALL REAR STABILIZER LINK ASSEMBLY LH Installation

36. INSTALL REAR SPEED SENSOR Installation

37. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY Installation

38. INSTALL REAR AXLE SHAFT NUT Installation

39. STABILIZE SUSPENSION Installation

40. FULLY TIGHTEN NO. 1 REAR UPPER CONTROL ARM ASSEMBLY Installation

41. FULLY TIGHTEN NO. 1 REAR SUSPENSION ARM ASSEMBLY Installation

42. FULLY TIGHTEN NO. 2 REAR SUSPENSION ARM ASSEMBLY Installation

43. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
(a) Connect the No. 3 parking brake cable assembly to the parking brake equalizer.





(b) Install the No. 3 parking brake cable assembly to the body with the 3 bolts and 2 clamps.
Bolt (A) - Torque: 6.0 Nm (61 kgf-cm, 53 in-lbf)
Bolt (B) - Torque: 19 Nm (194 kgf-cm, 14 ft-lbf)
44. INSTALL REAR SUSPENSION MEMBER BRACE LH






(a) Install the rear suspension member brace LH with the 2 bolts.
Torque: 50 Nm (510 kgf-cm, 37 ft-lbf)
45. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
2GR-FSE: Installation
4GR-FSE: Installation
46. INSTALL TAIL EXHAUST PIPE ASSEMBLY Installation

47. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation

48. INSTALL HEATED OXYGEN SENSOR (for 2WD) Installation

49. INSTALL HEATED OXYGEN SENSOR (for 4WD) Installation

50. INSTALL FRONT CENTER FLOOR BRACE Installation

51. INSTALL REAR NO. 1 FLOOR PANEL BRACE Installation

52. ADD DIFFERENTIAL OIL Adjustments

53. INSPECT DIFFERENTIAL OIL Adjustments

54. INSTALL NO. 2 DIFFERENTIAL SUPPORT PROTECTOR Installation

55. INSTALL REAR WHEEL
Torque: 103 Nm (1,050 kgf-cm, 76 ft-lbf)
56. INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission) Adjustments

57. ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission) Adjustments

58. INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transmission) Adjustments

59. ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transmission) Adjustments

60. CHECK FOR EXHAUST GAS LEAK
61. INSPECT AND ADJUST REAR WHEEL ALIGNMENT Rear Wheel Alignment
62. CHECK ABS SPEED SENSOR SIGNAL
with VDIM: Test Mode Procedure
without VDIM: Test Mode Procedure