Instrument Panel, Gauges and Warning Indicators: Description and Operation
METER: METER / GAUGE SYSTEM:
SYSTEM DIAGRAM
Input and output signals of the combination meter assembly:
*1: with Intelligent AFS
*2: with Clearance Sonar System
*3: with Sliding Roof
*4: with Power Tilt & Power Telescopic
*5: with Dynamic Radar Cruise Control System
*6: without VDIM
*7: with VDIM
*8: with Pre-collision System
*9: for 4WD
*10: without Navigation System
*11: with Navigation System
SYSTEM DESCRIPTION
1. METER GAUGE
METER/GAUGE
WARNING/INDICATOR
HINT:
- The multi-information display is located in the center of the combination meter assembly.
- The display shows a message or animation for each of the functions described in the table below.
MULTI-INFORMATION DISPLAY
ODO/TRIP Display
*1: without VDIM
*2: with VDIM
*3: without Navigation System
*4: with Navigation System
*5: for U.S.A.
*6: for Canada
*7: with Intelligent AFS
*8: with Pre-collision System
*9: with Dynamic Radar Cruise Control System
2. ILLUMINATION CONTROL
HINT: If the engine switch on (IG), the illumination control operates as follows. However, all illuminations other than the tachometer needle turn off while cranking the engine.
(a) The speedometer and tachometer needles illuminate starting from the base of the needles and moving to their tips.
(b) These needles move to their maximum position and return to zero.
(c) The fuel gauge and water temperature gauge light up, then the warning lights, indicator lights, multi-information display, and meter panel illumination come on.
3. MULTI-INFORMATION DISPLAY
*1: for Automatic Transmission
*2: with Clearance Sonar System
*3: with Intelligent AFS
*4: with Dynamic Radar Cruise Control System
*5: for 4WD
4. INTEGRATION CONTROL & PANEL ASSEMBLY (without NAVIGATION SYSTEM)/MULTI-DISPLAY (with NAVIGATION SYSTEM)
HINT:
- Integration control & panel assembly (*1) consists of two parts (passenger information display and heater control panel). These areas display the contents given in the table below.
- Multi-display (*2) consists of four parts (navigation display, passenger information display, clock display, and heater control panel). These areas display the contents given in the table below.
*1: without Navigation System
*2: with Navigation System
5. MULTI-INFORMATION DISPLAY FLOW-CHART
(a) Each warning indication for English
HINT: Illustrations may differ from the actual screen displayed depending on the specifications of the vehicle.
(b) Each warning indication for French
6. DIAGNOSIS SYSTEM
(a) for English
(b) for French
(c) The combination meter assembly indicates the diagnosis mode by blinking the warning light or by blinking the warning message in the multi-information display.
HINT:
- The multi-information display shows "DIAG" when the engine switch is on (IG) Diagnosis System.
- Diagnosis information can be displayed on the multi-information display after connecting a jumper wire between TC (J21-13) and CG (J21-4) of the DLC3 connector.
7. SATELLITE SWITCH
(a) By using satellite switch (RH switch, ON/OFF switch, LH switch), 5 different switch functions can be displayed and changed (SPEED indicator, TACH indicator, Tire pressure (*1), Sonar (*2), AFS (*3)).
HINT:
- *1: with Tire Pressure Warning System
- *2: with Clearance Sonar System
- *3: with Intelligent AFS
- When the engine switch on (IG) while driving at 3 mph (5 km/h) or less, the switch except for SONAR can be displayed.
- The switch functions displayed are changed in the order shown in the illustration using the satellite switch (RH switch, LH switch). The function can be set using the ON/OFF switch.
- The display automatically returns to the previous display 6 seconds after the satellite switch is operated. It will return to the previous display immediately if the DISP switch is operated.
(b) SPEED and TACH indicator
- The SPEED indicator and TACH indicator come on when the vehicle speed or engine speed reaches the speed set using the satellite switch. The setting ranges of these indicators are shown in the table that follows.
- Vehicle speed or engine speed can be set using the satellite switch.
- These indicators consist of yellow and red dots that are arranged to form indicator rings.
- When the set vehicle speed or engine speed is reached while driving, the red and yellow dots will turn on at the same time to cause amber light to illuminate the indicator ring.
- However, if the vehicle or engine speed is set to the maximum speed of the indicator setting range, and the speed reaches this set speed, only red light will illuminate the indicator ring.
HINT: Customize Parameters
Speed Indicator:
Tach Indicator:
HINT: Customize Parameters