Navigation System
DIAGNOSTIC TROUBLE CODE CHART
1. MULTI DISPLAY (Physical address: 110)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine
- *2: This code is stored when 180 sec. has passed after the power supply connector is pulled out after engine start.
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: This code may be stored when the engine key is turned again 1 mm. after engine start.
Diagnosis Item:
a. Logical address: 01 (Communication control)
Diagnosis Item:
b. Logical address: 21 (Switch)
Diagnosis Item:
c. Logical address: 34 (Front passenger monitor)
2. GATEWAY ECU (Physical address: 1C6)
HINT:
*1: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
Diagnosis Item:
Logical address: 01 (Communication control)
3. RADIO AND PLAYER (Physical address: 190)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code is stored when 180 sec. has passed after the power supply connector is pulled out after engine start.
- *3: This code may be stored when the engine key is turned again 1 mm. after engine start.
- *4: This code may be stored when the engine key is turned again after engine start.
- *5: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
Diagnosis Item (Part 1):
Diagnosis Item (Part 2):
a. Logical address: 01 (Communication control)
Diagnosis Item:
b. Logical address: 61 (Cassette tape players switch)
Diagnosis Item:
c. Logical address: 63 (In-dash CD changer)
4. NAVIGATION ECU (Physical address: 178)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting the engine.
- *2: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
- *3: This code may be stored when the engine key is turned 1 mm. again after engine start.
- *4: This code may be stored when the engine key is turned again after engine start.
Diagnosis Item:
a. Logical address: 01 (Communication control)
Diagnosis Item:
b. Logical address: 80 (Navigation ECU)
Diagnosis Item:
c. Logical address: 80 (GPS receiver)
5. STEREO COMPONENT AMPLIFIER (Physical address: 440)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code may be stored when the engine key is turned again 1 mm. after engine start.
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: When 210 Sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
Diagnosis Item:
Logical address: 01 (Communication control)
6. STEREO COMPONENT TURNER (Physical address: 1FO)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code may be stored when the engine key is turned again 1 mm. after engine start.
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
Diagnosis Item:
Logical address: 01 (Communication control)
7. AUDIO AND REAR A/C CONTROL SWITCH (Physical address: 1CO)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code may be stored when the engine key is turned again 1 mm. after engine start.
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
Diagnosis Item:
Logical address: 01 (Communication control)
8. TELEPHONE ECU (Physical address :17C)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code may be stored when the engine key is turned again 1 mm. after engine start.
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
Diagnosis Item:
Logical address: 01 (Communication control)