FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Infiniti >> 2013 >> G37 Convertible V6-3.7L (VQ37VHR) >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P0441

P0441




P0441 EVAP CONTROL SYSTEM

DTC Logic


DTC DETECTION LOGIC

NOTE:
If DTC P0441 is displayed with other DTC such as P2122, P2123, P2127, P2128 or P2138, first perform trouble diagnosis for other DTC.
In this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions.
Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP
canister purge volume control solenoid valve is open to admit purge flow. Purge flow exposes the EVAP control system pressure sensor to intake manifold vacuum.
Under normal conditions (non-closed throttle), sensor output voltage indicates if pressure drop and purge flow are adequate. If not, a malfunction is determined.











DTC CONFIRMATION PROCEDURE


1. INSPECTION START

Do you have CONSULT?
Do you have CONSULT?
YES- GO TO 2.
NO- GO TO 6.

2. PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.





- GO TO 3.

3. PERFORM DTC CONFIRMATION PROCEDURE-I

With CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Turn ignition switch OFF and wait at least 10 seconds.
3.Turn ignition switch ON.
4.Turn ignition switch OFF and wait at least 10 seconds.
5.Start engine and let it idle for at least 70 seconds.
6.Select "PURG FLOW P0441" of "EVAPORATIVE SYSTEM" in "DTC WORK SUPPORT" mode with CONSULT.
7.Touch "START".
Is "COMPLETED" displayed on CONSULT screen?
YES- GO TO 5.
NO- GO TO 4.

4. PERFORM DTC CONFIRMATION PROCEDURE-II

When the following conditions are met, "TESTING" will be displayed on the CONSULT screen. Maintain the conditions continuously until "TESTING" changes to "COMPLETED". (It will take at least 35 seconds.)






CAUTION:
Always drive vehicle at a safe speed.
Is "COMPLETED" displayed on CONSULT screen?
YES- GO TO 5.
NO- Perform DTC CONFIRMATION PROCEDURE again. GO TO 3.

5. PERFORM DTC CONFIRMATION PROCEDURE-III

Touch "SELF-DIAG RESULTS".
Which is displayed on CONSULT screen?
OK- INSPECTION END
NG- Go to "Diagnosis Procedure" .

6. PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to "Component Function Check" .
NOTE:
Use component function check to check the overall monitoring function of the EVAP control system purge flow monitoring. During this check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES- INSPECTION END
NO- Go to "Diagnosis Procedure" .


Component Function Check


1. PERFORM COMPONENT FUNCTION CHECK

Without CONSULT
1.Lift up drive wheels.
2.Start engine (VDC switch OFF) and warm it up to normal operating temperature.
3.Turn ignition switch OFF and wait at least 10 seconds.
4.Turn ignition switch ON.
5.Turn ignition switch OFF and wait at least 10 seconds.
6.Start engine and wait at least 70 seconds.
7.Set voltmeter probes to ECM harness connector terminals as per the following.





8.Check EVAP control system pressure sensor value at idle speed and note it.
9.Establish and maintain the following conditions for at least 1 minute.





10.Verify that EVAP control system pressure sensor value stays 0.1 V less than the value at idle speed (measured at step 8) for at least 1 second.
Is the inspection result normal?
YES- INSPECTION END
NO- Go to "Diagnosis Procedure" .


Diagnosis Procedure


1. CHECK EVAP CANISTER

1.Turn ignition switch OFF.
2.Check EVAP canister for cracks.
Is the inspection result normal?
YES-1- With CONSULT: GO TO 2.
YES-2- Without CONSULT: GO TO 3.
NO- Replace EVAP canister. Refer to "Removal and Installation" Removal and Installation.

2. CHECK PURGE FLOW

With CONSULT
1.Disconnect vacuum hose connected to EVAP canister purge volume control solenoid valve at EVAP service port.
2.Start engine and let it idle.
3.Select "PURG VOL CONT/V" in "ACTIVE TEST" mode with CONSULT.
4.Touch "Qd" and "Qu" on CONSULT screen to adjust "PURG VOL C/V" opening and check vacuum existence.





Is the inspection result normal?
YES- GO TO 7.
NO- GO TO 4.

3. CHECK PURGE FLOW

Without CONSULT
1.Start engine and warm it up to normal operating temperature.
2.Stop engine.
3.Disconnect vacuum hose connected to EVAP canister purge volume control solenoid valve at EVAP service port and install vacuum gauge. For the location of EVAP service port, refer to "System Diagram" System Diagram.
4.Start engine and let it idle.
Do not depress accelerator pedal even slightly.
5.Check vacuum gauge indication before 60 seconds passed after starting engine.

Vacuum should not exist.

6.Revving engine up to 2,000rpm after 100 seconds passed after starting engine.

Vacuum should exist.

Is the inspection result normal?
YES- GO TO 7.
NO- GO TO 4.

4. CHECK EVAP PURGE LINE

1.Turn ignition switch OFF.
2.Check EVAP purge line for improper connection or disconnection.
Refer to "System Diagram" System Diagram.
Is the inspection result normal?
YES- GO TO 5.
NO- Repair it.

5. CHECK EVAP PURGE HOSE AND PURGE PORT






1.Disconnect purge hoses connected to EVAP service port A and
EVAP canister purge volume control solenoid valve B.
2.Blow air into each hose and EVAP purge port C.





3.Check that air flows freely.
Is the inspection result normal?
YES-1- With CONSULT: GO TO 6.
YES-2- Without CONSULT: GO TO 7.
NO- Repair or clean hoses and/or purge port.

6. CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE

With CONSULT
1.Start engine.
2.Perform "PURG VOL CONT/V" in "ACTIVE TEST" mode with CONSULT. Check that engine speed varies according to the valve opening.
Does engine speed vary according to the valve opening?
YES- GO TO 8.
NO- GO TO 7.

7. CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE

Refer to "Component Inspection" P0443.
Is the inspection result normal?
YES- GO TO 8.
NO- Replace EVAP canister purge volume control solenoid valve.

8. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR

1.Disconnect EVAP control system pressure sensor harness connector.
2.Check connectors for water.

Water should not exist.

Is the inspection result normal?
YES- GO TO 9.
NO- Replace EVAP control system pressure sensor. Refer to "Exploded View" Exploded View.

9. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR FUNCTION

Refer to "DTC Logic" P0452 for DTC P0452, "DTC Logic" P0453 for DTC P0453.
Is the inspection result normal?
YES- GO TO 10.
NO- Replace EVAP control system pressure sensor. Refer to "Exploded View" Exploded View.

10. CHECK RUBBER TUBE FOR CLOGGING

1.Disconnect rubber tube connected to EVAP canister vent control valve.
2.Check the rubber tube for clogging.
Is the inspection result normal?
YES- GO TO 11.
NO- Clean the rubber tube using an air blower.

11. CHECK EVAP CANISTER VENT CONTROL VALVE

Refer to "Component Inspection" P0447.
Is the inspection result normal?
YES- GO TO 12.
NO- Replace EVAP canister vent control valve. Refer to "Exploded View" Exploded View.

12. CHECK EVAP PURGE LINE

Inspect EVAP purge line (pipe and rubber tube). Check for evidence of leaks.
Refer to "System Diagram" System Diagram.
Is the inspection result normal?
YES- GO TO 13.
NO- Replace it.

13. CLEAN EVAP PURGE LINE

Clean EVAP purge line (pipe and rubber tube) using air blower.
- GO TO 14.

14. CHECK INTERMITTENT INCIDENT

Refer to "Intermittent Incident" Intermittent Incident.
- INSPECTION END
pro multis Credits:Operation CHARM About Operation CHARM