Front Seat Belt Replacement

Front Seat Belt Replacement

Front Seat Belt - 2-door

SRS components are located in this area. Review the SRS component locations SRS Component Location Index (4-Door) and the precautions and procedures Technician Safety Information before doing repairs or service.

NOTE:

- Check the front seat belts for damage, Testing and Inspection and replace them if necessary.

- If replacing the front seat belt after deployment, refer to component replacement/inspection after deployment Service and Repair for a complete list of other parts that must also be replaced.

1. Do the battery terminal disconnection procedure, Procedures and wait at least 3 minutes before beginning work.

2. Slide the front seat forward fully.

3. Remove the seat belt lower anchor.
- Driver's seat belt: Remove the lower anchor cap (A), and remove the lower anchor bolt (B).

- Passenger's seat belt: Carefully insert the tip of a small screwdriver (C) through the hole in the back of the front seat belt lower anchor cover (D), and into the hole in the front seat belt lower anchor (E). Unlock the lower anchor by pushing in on the screwdriver. Remove the screwdriver, and then detach the front seat belt anchor plate (F) and the anchor cover from the lower anchor.

4. Remove these items:
- Door sill trim Interior Trim Removal/Installation - Door Sill Area (2-Door)

- Rear side trim panel Interior Trim Removal/Installation - Rear Side Area (2-Door)

Driver's seat

Passenger's seat

5. Remove the bolts (A) and the seat belt guide (B).

6. Remove the upper anchor cap (A), and remove the upper anchor bolt (B).

7. Disconnect the seat belt tensioner connector (A). Remove the upper retractor mounting bolt (B) and the lower retractor bolt (C), then remove the front seat belt (D) and retractor (E).

8. If necessary, remove the front seat belt protector (F).

9. Install the belt in the reverse order of removal, and note these items:
- Check that the retractor locking mechanism functions as described. Testing and Inspection

- Assemble the washers, the collars, and the bushings on the upper and lower anchor bolts as shown.

- If the seat belt tensioner has deployed, replace the front seat belt protector with a new one.

- Apply medium strength liquid thread lock to the anchor bolts before reinstallation.

- Before installing the anchor bolts, make sure there are no twists or kinks in the front seat belt.

- Make sure the seat belt tensioner connector is plugged in properly.

- Passenger's seat belt: The triangle marks (A) on the anchor plate (B) and on the lower anchor (C) must face the same side.

- Passenger's seat belt: Insert the hook on the anchor plate into the lower anchor, and be sure that the lower anchor is locked securely.

- Check for any DTCs that may have been set during repairs, and clear them.

- Do the battery terminal reconnection procedure. Procedures

Upper anchor bolt installation

Lower anchor bolt installation

Front seat belt lower anchor installation

Front Seat Belt - 4-door

SRS components are located in this area. Review the SRS component locations SRS Component Location Index (4-Door) and the precautions and procedures Technician Safety Information before doing repairs or service.

NOTE:

- Check the front seat belts for damage, Testing and Inspection and replace them if necessary.

- If replacing the front seat belt after deployment, refer to component replacement/inspection after deployment Service and Repair for a complete list of other parts that must also be replaced.

1. Do the battery terminal disconnection procedure, Procedures and wait at least 3 minutes before beginning work.

2. Slide the front seat forward fully, and remove the anchor cover (A).

3. Remove the lower anchor bolt (A).

4. Remove the B-pillar lower trim. Interior Trim Removal/Installation - B-Pillar Upper/Lower Trim

5. Remove the B-pillar upper trim and slider. Interior Trim Removal/Installation - B-Pillar Upper/Lower Trim

6. Remove the upper anchor bolt (A).

9. Remove the shoulder anchor adjuster (A).

10. Install the seat belt in the reverse order of removal, and note these items:
- Apply medium strength liquid thread lock to the anchor bolts before reinstallation.

- Tighten the bolts by hand first, then tighten to the specified torque.

- Check that the retractor locking mechanism functions as described. Testing and Inspection

- Assemble the washer, the collar, and the bushing on the upper anchor bolt as shown.

- If the seat belt tensioner has been deployed, replace the front seat belt protector with a new one.

- Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.

- Make sure the seat belt tensioner is properly plugged in.

- Check for any DTCs that may have been set during repairs, and clear them.

- Do the battery terminal reconnection procedure. Procedures

Upper anchor bolt installation

Front Seat Belt Buckle

SRS components are located in this area. Review the SRS component locations SRS Component Location Index (4-Door) and the precautions and procedures Technician Safety Information before doing repairs or service.

NOTE: If replacing the front seat belt buckle after deployment, refer to component replacement/inspection after deployment Service and Repair for a complete list of other parts that must also be replaced.

1. Do the battery terminal disconnection procedure, Procedures and wait at least 3 minutes before beginning work.

2. Remove the front seat. Front Seat Removal/Installation

3. Lift up the front seat, then detach the seat belt switch connector (A) and seat belt buckle tensioner connector (B), and on the driver's seat, detach the harness clip (C).

Driver's seat

Passenger's seat

4. Remove the center anchor bolt (A), then remove the seat belt buckle (B) from the elastic band (C).

5. 2-door passenger's seat: Release the hook strips (D) and pull back the seat cushion cover.

6. Pull the seat belt switch harness (E) out through the space between the seat cushion and the seat track (driver's seat), or through the hole in the seat track (passenger's seat).

Except 2-door passenger's seat

2-door passenger's seat

7. Install the buckle in the reverse order of removal, and note these items:
- Assemble the washers on the center anchor bolt as shown.

- Apply medium strength liquid thread lock to the center anchor bolt before reinstallation.

- Tighten the bolts by hand first, then tighten to specification with a torque wrench.

- Make sure the seat belt switch connector and seat belt buckle tensioner connector are plugged in properly.

- Check for any DTCs that may have been set during repairs, and clear them.

- Do the battery terminal reconnection procedure. Procedures

Center anchor bolt installation

Passenger's Seat Belt Lower Anchor

1. Remove the door sill trim. Interior Trim Removal/Installation - Door Sill Area (2-Door)

2. Remove the lower anchor bolt (A), then remove the lower anchor (B).

3. Install the lower anchor in the reverse order of removal, and note these items:
- Apply medium strength liquid thread lock to the lower anchor bolt before reinstallation.

- Assemble the washers, the collars, and the bushing on the lower anchor bolt as shown.

Lower anchor bolt installation