Pinpoint Test AM: DTC B111D
Seats
Pinpoint Tests
Pinpoint Test AM: DTC B111D
Refer to Wiring Diagram Set 119, Climate Controlled Seats for schematic and connector information. Diagrams By Number
Normal Operation
The Dual Climate Controlled Seat Module (DCSM) monitors the blower circuits. If a short to ground on any of these circuits is detected, the DTC will be set.
- DTC B111D (Passenger Blower Driver Overtemperature) - If the DCSM output circuits to the passenger seat blower or any components within these circuit loops are shorted to ground or cause an excessive current draw, the DCSM will overheat, shut down the passenger seat system and set this DTC.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Thermo-Electric Device (TED) assembly
- DCSM
PINPOINT TEST AM: DTC B111D
NOTICE: When taking measurements at Dual Climate Controlled Seat Module (DCSM) harness connectors, do not insert the electrical probes into the female connector pins. Inserting the probes into connector pins can cause intermittent or open electrical connections after reassembly resulting in Diagnostic Trouble Codes (DTCs) and system failure. Touching the tip of these connector pins is recommended instead.
NOTE: The air bag warning indicator illuminates when the correct Restraints Control Module (RCM) fuse is removed and the ignition switch is ON.
NOTE: The Supplemental Restraint System (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.
-------------------------------------------------
AM1 CHECK THE BLOWER MOTOR FEED CIRCUIT FOR A SHORT TO GROUND
- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of Restraint Systems.
- Disconnect: Passenger Seat Side Air Bag C339.
- Disconnect: Passenger Seat Safety Belt Buckle Pretensioner C3066.
- Disconnect: DCSM C3265C.
- Disconnect: Cushion TED C3040.
- Disconnect: Backrest TED C3039.
- Measure the resistance between DCSM C3265C-8, circuit CHS08 (BN/YE), harness side and ground.
- Is the resistance greater than 10,000 ohms?
Yes
GO to AM2.
No
REPAIR the circuit. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger seat safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C339.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
AM2 CHECK FOR A SHORT BETWEEN THE BLOWER MOTOR FEED AND GROUND CIRCUITS
- Measure the resistance between DCSM C3265C-7, circuit RHS08 (VT/WH), harness side and C3265C-8, circuit CHS08 (BN/YE), harness side.
- Is the resistance greater than 10,000 ohms?
Yes
GO to AM3.
No
REPAIR the circuits. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger seat safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C339.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
AM3 CHECK THE BACKREST CUSHION BLOWER MOTOR RESISTANCE
- NOTE: The ohmmeter must be connected with the positive lead to pin 2 and the negative lead to pin 4 when measuring. Ohmmeter leads incorrectly connected will result in false readings and lead to incorrect identification of components that are not faulty.
- Measure the resistance between:
- cushion TED C3040 pin 2 and pin 4, component side.
- backrest TED C3039 pin 2 and pin 4, component side.
- Are the resistances between 4,000 and 10,000 ohms?
Yes
INSTALL a new DCSM. REFER to Dual Climate Controlled Seat Module (DCSM) Dual Climate Controlled Seat Module (DCSM). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger seat safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C339.
REPOWER the SRS. REFER to Restraint Systems.
No
If cushion TED resistance is not between 4,000 and 10,000 ohms, INSTALL a new cushion TED. REFER to Seat Cushion Thermo-Electric Device Seat Cushion Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
If backrest TED resistance is not between 4,000 and 10,000 ohms, INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device Seat Backrest Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger seat safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C339.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------