Pinpoint Test N: One Turn Signal/Hazard Lamp Is Inoperative/Always On
Turn Signal and Hazard Lamps
Pinpoint Tests
Pinpoint Test N: One Turn Signal/Hazard Lamp Is Inoperative/Always On
Refer to Wiring Diagram Set 90, Turn Signal/Stop/Hazard Lamps for schematic and connector information. Diagrams By Number
Normal Operation
When the Smart Junction Box (SJB) detects the multifunction switch is in the LH TURN position, the SJB provides voltage to the LH front turn lamp. When the SJB detects the multifunction switch is in the RH TURN position, the SJB provides voltage to the RH front turn lamp. The rear turn lamps are controlled utilizing the rear stoplamp circuitry.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Bulb holder
- SJB
PINPOINT TEST N: ONE TURN SIGNAL/HAZARD LAMP IS INOPERATIVE/ALWAYS ON
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
-------------------------------------------------
N1 DETERMINE IF A TURN LAMP IS ALWAYS ON
- Ignition ON.
- Monitor the turn lamps.
- Is either front turn lamp always on?
Yes
GO to N2.
No
GO to N3.
-------------------------------------------------
N2 CHECK THE SJB TURN LAMP OUTPUT CIRCUIT FOR A SHORT TO VOLTAGE
- Ignition OFF.
- Disconnect: SJB C2280f.
- Ignition ON.
- Does the front turn lamp in question continue to illuminate?
Yes
REPAIR circuit CLS21 (BU/GN) (LH front turn lamp) or circuit CLS25 (YE/VT) (RH front turn lamp) for a short to voltage. CLEAR the DTCs. REPEAT the self-test.
No
GO to N9.
-------------------------------------------------
N3 USE THE RECORDED DTCs FROM THE SJB SELF-TEST
- Check the recorded results from the SJB on-demand self-test.
- Was DTC B2A27 or DTC B2A29 present?
Yes
GO to N6.
No
GO to N4.
-------------------------------------------------
N4 CHECK THE BULB HOLDER FOR A SHORT TO GROUND
- Disconnect: Inoperative Front Turn Lamp.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: SJB Self-Test.
- Clear the DTCs and repeat the self-test (required to enable the turn lamp output driver if DTC B106E is present)
- Activate the hazard flasher lamp function.
- Measure the voltage between the LH front turn lamp C1023-3, circuit CLS21 (BU/GN), harness side and ground; or between the RH front turn lamp C1043-3, circuit CLS25 (YE/VT), harness side and ground.
- Does the voltage alternate from 0 volts to greater than 10 volts?
Yes
INSTALL a new bulb holder. TEST the system for normal operation.
No
GO to N5.
-------------------------------------------------
N5 CHECK THE SJB TURN LAMP OUTPUT CIRCUIT FOR A SHORT TO GROUND
- Turn the hazard lamps off.
- Disconnect: SJB C2280f.
- Measure the resistance between the LH front turn lamp C1023-3, circuit CLS21 (BU/GN), harness side and ground; or between the RH front turn lamp C1043-3, circuit CLS21 (BU/GN), harness side and ground.
- Is the resistance greater than 10,000 ohms?
Yes
GO to N9.
No
REPAIR circuit CLS21 (BU/GN) (LH turn) or circuit CLS25 (YE/VT) (RH turn) for a short to ground. CLEAR the DTCs. REPEAT the self-test
After the repair:
If no DTCs are present, TEST the system for normal operation
If DTC B106E is present, CLEAR the DTCs and REPEAT the self-test (required to enable the turn lamp output driver if DTC B106E is present). TEST the system for normal operation.
If DTC B106F is present, INSTALL a new SJB. REFER to Body Control Systems. TEST the system for normal operation.
-------------------------------------------------
N6 CHECK FOR VOLTAGE TO THE FRONT TURN LAMP
- Ignition OFF.
- Disconnect: Inoperative Front Turn Lamp.
- Ignition ON.
- Turn the hazard lamps on.
- Measure the voltage between the LH front turn lamp C1023-3, circuit CLS21 (BU/GN), harness side and ground; or between the RH front turn lamp C1043-3, circuit CLS25 (YE/VT), harness side and ground.
- Does the voltage alternate from 0 volts to greater than 10 volts?
Yes
GO to N7
No
GO to N8.
-------------------------------------------------
N7 CHECK FOR VOLTAGE TO THE FRONT TURN LAMP USING THE CONNECTOR GROUND
- Measure the voltage between the LH front turn lamp C1023-3, circuit CLS21 (BU/GN), harness side and the LH front turn lamp C1023-1, circuit GD129 (BK/YE) harness side; or between the RH front turn lamp C1043-3, circuit CLS25 (YE/VT), harness side and the RH front turn lamp C1043-1, circuit GD129 (BK/YE) harness side.
- Does the voltage alternate from 0 volts to greater than 10 volts?
Yes
INSTALL a new bulb holder. CLEAR the DTCs. REPEAT the self-test.
No
REPAIR circuit GD129 (BK/YE) for an open. CLEAR the DTCs. REPEAT the self-test.
-------------------------------------------------
N8 CHECK THE SJB TURN LAMP OUTPUT CIRCUIT FOR AN OPEN
- Turn the hazard lamps off.
- Disconnect: SJB C2280f.
- Measure the resistance between the LH front turn lamp C1023-3, circuit CLS21 (BU/GN), harness side and the SJB C2280f-21, circuit CLS21 (BU/GN), harness side; or between the RH front turn lamp C1043-3, circuit CLS21 (BU/GN), harness side and the SJB C2280f-23, circuit CLS25 (YE/VT), harness side.
- Is the resistance less than 5 ohms?
Yes
GO to N9.
No
REPAIR circuit CLS21 (BU/GN) (LH turn) or circuit CLS25 (YE/VT) (RH turn) for an open. CLEAR the DTCs. REPEAT the self-test
-------------------------------------------------
N9 CHECK FOR CORRECT SJB OPERATION
- Disconnect all the SJB connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the SJB connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new SJB. REFER to Body Control Systems. TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
-------------------------------------------------