Brake Rotor/Disc: Testing and Inspection
DIAGNOSIS AND TESTING - BRAKE ROTOR
Special Tools:
Any servicing of the rotor requires extreme care to maintain the rotor within service tolerances to ensure proper brake action.
Excessive runout or wobble in a rotor can increase pedal travel due to piston knock-back. This increases guide pin sleeve wear due to the tendency of the caliper to follow the rotor wobble.
When diagnosing a brake noise or pulsation, the machined disc braking surface should be inspected.
BRAKING SURFACE INSPECTION
Light braking surface scoring and wear is acceptable. If heavy scoring or warping is evident, the rotor must be refaced or replaced Procedures.
Excessive wear and scoring of the rotor can cause improper lining contact on the rotor's braking surface. If the ridges on the rotor are not removed before new brake shoes are installed, improper wear of the shoes will result.
If a vehicle has not been driven for a period of time, the rotor's braking surface will rust in the areas not covered by the brake shoes at that time. Once the vehicle is driven, noise and chatter from the disc brakes can result when the brakes are applied.
Some discoloration or wear of the rotor surface is normal and does not require resurfacing when linings are replaced. If cracks or burned spots are evident, the rotor must be replaced.
ROTOR MINIMUM THICKNESS
Measure rotor thickness (1) at the center of the brake shoe contact surface. Replace the rotor if it is worn below minimum thickness or if machining the rotor will cause its thickness to fall below specifications.
CAUTION: Do not machine the rotor if it will cause the rotor to fall below minimum thickness.
Most minimum thickness specifications (1) are cast into the rotor's unmachined surface (2). Some brake rotors have the minimum thickness specification located elsewhere. Limits can also be found in this component's specification table [1][2]Brake Rotor/Disc
ROTOR THICKNESS VARIATION
Thickness variation in a rotor's braking surface can result in pedal pulsation, chatter and surge. This can also be caused by excessive runout in the rotor or the hub.
Rotor thickness variation measurements should be made in conjunction with measuring runout. Measure thickness of the brake rotor (2) at 12 equal points around the rotor braking surface with a micrometer (1) at a radius approximately 25 mm (1 inch) from edge of rotor. If thickness measurements vary beyond the specification listed in the specification table [1][2]Brake Rotor/Disc , the rotor should be refaced or replaced. Procedures.
ROTOR RUNOUT
On-vehicle rotor runout is the combination of the individual runout of the hub face and the runout of the brake rotor (hub runout can be measured separately). To measure rotor runout on the vehicle:
1. Raise and support vehicle. Maintenance
2. Remove tire and wheel assembly. Tires And Wheels - Removal
3. Install standard wheel mounting nuts, flat side to rotor, on all studs (2). Progressively tighten nuts to 150 Nm (110 ft. lbs.) torque.
4. Mount Dial Indicator (1), Special Tool , with Wheel, Special Tool , or equivalent, to knuckle. Position Dial Indicator Wheel to contact rotor braking surface approximately ten millimeters from outer edge of rotor (3).
5. Slowly rotate brake rotor checking lateral runout, marking the low and high spots. Record these measurements.
6. Check and record runout of opposite side of rotor in same fashion, marking the low and high spots.
7. Compare runout measurement to specifications.[1][2]Brake Rotor/Disc
If runout is in excess of specifications, check the lateral runout of the hub face. Before removing the rotor from the hub, place a chalk mark across both the rotor (1) and the one wheel stud (2) closest to where the high runout measurement was taken. This way, the original mounting spot of the rotor on the hub is indexed.
8. Remove the rotor from the hub. Brake Rotor - Removal
NOTE: Before measuring hub runout, clean the hub face surface with an appropriate cleaner. This provides a clean surface to get an accurate indicator reading.
9. Mount Dial Indicator (2), Special Tool , to the knuckle. Position Dial Indicator stem so it contacts hub face (1) near outer diameter. Care must be taken to position stem outside of stud circle, but inside of chamfer on the hub rim.
10. Slowly rotate hub measuring runout. Hub runout should not exceed 0.01 mm (0.0004 inch). If runout exceeds this specification, the hub must be replaced. Rear Hub And Bearing - Removal
11. If hub runout does not exceed this specification, install original rotor back on hub, aligning chalk mark on rotor (2) with a wheel mounting stud, two studs apart from original stud (1).
12. Install standard wheel mounting nuts, flat side to rotor, on all studs (2). Progressively tighten nuts to 150 Nm (110 ft. lbs.) torque.
13. Mount Dial Indicator (1) and remeasure runout on both sides of the brake rotor as explained in earlier steps to see if runout is now within specifications. [1][2]Brake Rotor/Disc
14. If runout is still not within specifications, reface or replace brake rotor. Procedures