P0505

Diagnostic Chart (Part 1 Of 2):

Diagnostic Chart (Part 2 Of 2):

Schematic:

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) controls the Idle Air Control (IAC) valve in order to regulate the air flow through the idle air bypass passage. The amount of air flowing through the idle air bypass passage determines the idle speed. The PCM directs the IAC valve according to changes in the engine load. A stalling or poor idle concern may be caused by the IAC valve not operating properly.

CONDITIONS FOR RUNNING THE DTC
^ The Barometric Pressure (BARO) is more than 75 kPa.
^ The Intake Air Temperature is more than -8°C (+18°F).
^ The Engine Coolant Temperature is more than 70°C (158°F).
^ The engine is running in Closed Loop.
^ The throttle is closed.
^ The A/C is Off.
^ The Power Steering Pressure (PSP) switch is Off.

CONDITIONS FOR SETTING THE DTC
The actual engine speed is 100 RPM less than the target engine speed value for more than 20 seconds.

OR

The actual engine speed is 200 RPM more than the target engine speed value for more than 20 seconds.

ACTION TAKEN WHEN THE DTC SETS
^ The PCM illuminates the Malfunction Indicator Lamp (MIL) after 2 consecutive ignition cycles in which the diagnostic runs with the fault active.
^ The PCM records the operating conditions at the time the diagnostic fails. This information is stored in the Freeze Frame buffer.

CONDITIONS FOR CLEARING THE MIL/DTC
^ The MIL turns off after 3 consecutively passing trips without a fault present.
^ A history DTC clears after 40 consecutive warm-up cycles without a fault.
^ Perform the scan tool Clear DTC Information function.

DIAGNOSTIC AIDS
The IAC Duty Cycle parameter of the scan tool will appear fixed when a Current or Pending DTC P0505 is set. Clear the DTC in order to observe present time IAC Duty Cycle readings.

If the DTC P0505 is intermittent, driving the vehicle under the following conditions can verify whether the fault is present. Perform the scan tool Clear DTC Information function. Road test the vehicle while monitoring the DTC P0505 diagnostic on the scan tool under the Not Ran Since Code Cleared selection in the DTC Information menu.

If DTC P0505 appears in the Not Ran Since Code Cleared list, the P0505 diagnostic has not yet run. When the DTC P0505 does not appear in the Not Ran Since Code Cleared list, the P0505 diagnostic has run. If the MIL is NOT illuminated, and there is no Pending DTC Status in DTC Information, the P0505 diagnostic has passed. The DTCs MUST be cleared in order to view the Current Status of the Not Ran Since Code Cleared list. DO NOT forget that the Not Ran Since Code Cleared list only indicates that the test has run, not whether the test passed or failed. The DTC Information screen must be checked for Current or Pending status in order to determine the outcome of the diagnostic test involved.

An intermittent malfunction may be caused by a fault in the IAC system electrical circuits. Check for the following conditions:
^ Any backed-out terminals
^ Any improper mating of terminals
^ Any broken electrical connector locks
^ Any improperly formed or damaged terminals
^ Any faulty terminal-to-wire connections
^ Any physical damage to the wiring harness
^ A broken wire inside the insulation
^ Any corrosion of the electrical connections, the splices, or the terminals

IAC Valve Terminal (Pin) Location:

Use the table in order to locate the correct terminals to test during diagnosis. The table layout corresponds to the pin location of the IAC valve electrical terminals.

TEST DESCRIPTION
The numbers below refer to the step numbers in the diagnostic table.
1. The Powertrain OBD System Check prompts the technician to complete some basic checks and store the Freeze Frame data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
2. This step prompts the technician to check for any condition that can affect the ability of the IAC valve to control engine idle speed. A DTC P0505 can set even if there is no fault in the IAC system. Any condition that can affect the idle speed of the engine must be repaired first, in order to enable proper diagnosis of the DTC P0505.
4. This step tests whether the PCM can operate the IAC valve with the scan tool. The IAC valve can be commanded to increase and/or decrease engine speed by using the scan tool RPM Control function. The RPM Control function of the scan tool is disabled when any DTCs are set, and when the engine temperature is less than the normal operating temperature of 80°C (176°F).
5. This step checks whether the malfunction that caused the DTC P0505 is still present. Operating the vehicle under these conditions will verify whether the fault is present. After performing the scan tool Clear DTC Information function, the DTC P0505 diagnostic can be monitored on the scan tool under the Not Ran Since Code Cleared selection in the DTC Information menu. If DTC P0505 appears in the Not Ran Since Code Cleared list, the DTC P0505 diagnostic has not yet run. When DTC P0505 does not appear in the Not Ran Since Code Cleared list, the DTC P0505 diagnostic has run. If the MIL is NOT illuminated and there is no Pending DTC Status in DTC Information, the P0505 diagnostic has passed. The DTCs MUST be cleared in order to view the Current Status of the Not Ran Since Code Cleared list. DO NOT forget that the Not Ran Since Code Cleared list only indicates that the test has run, not whether the test passed or failed. The DTC Information screen must be checked for Current or Pending status in order to determine the outcome of the diagnostic test involved.
9. This step checks the electrical circuits between the IAC valve and the PCM.
10. This step determines whether the PCM is attempting to control the IAC valve. Each IAC coil control circuit should indicate a high voltage of 12 volts or more and then a low voltage of 0.0-1.0 volts as the PCM commands changes in the engine speed. Remember to clear any DTCs and run the engine until the engine reaches a normal operating temperature before attempting RPM control with the scan tool.
16. This step checks determines if the malfunction that caused DTC P0505 is still present. Road testing the vehicle under these conditions will verify whether the fault is present. After performing the scan tool Clear DTC Information function, the DTC P0505 diagnostic can be monitored on the scan tool under the Not Ran Since Code Cleared selection in the DTC Information menu. If DTC P0505 appears in the Not Ran Since Code Cleared list, the DTC P0505 diagnostic has not yet run. When DTC P0505 does not appear in the Not Ran Since Code Cleared list, the DTC P0505 diagnostic has run. If the MIL is NOT illuminated and there is no Pending DTC Status in DTC Information, the P0505 diagnostic has passed. The DTCs MUST be cleared in order to view the Current Status of the Not Ran Since Code Cleared list. DO NOT forget that the Not Ran Since Code Cleared list only indicates that the test has run, not whether the test passed or failed. The DTC Information screen must be checked for Current or Pending status in order to determine the outcome of the diagnostic test involved.