P0324
DTC P0324, P0326, or P06B6
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC P0324
-
Knock Sensor System Performance
DTC P0326
-
Knock Sensor Performance
DTC P06B6
-
Control Module Knock Sensor Processor Performance
Diagnostic Fault Information
Circuit/System Description
The knock sensor enables the engine control module (ECM) to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation. The knock sensor produces an alternating current (AC) voltage signal that varies depending on the vibration level during engine operation. The ECM adjusts the spark timing based on the amplitude and the frequency of the knock sensor signal. The ECM receives the knock sensor signal through 2 isolated circuits. The ECM learns a minimum knock sensor noise level for all of the engine speed ranges. The ECM monitors for a normal knock sensor signal. The ECM monitors the internal knock sensor processor by verifying a 20 KHz signal generated on the signal circuit is detected on the sensor low reference circuit.
Conditions for Running the DTC
P0324 and P0326-Condition 1
* Engine speed is between 600 and 8,500 RPM.
* Engine is running for greater than 2 s.
* The engine coolant temperature (ECT) is warmer than -40°C (-40°F).
* The intake air temperature (IAT) is warmer than -40°C (-40°F).
* The DTCs run continuously when the above conditions are met.
P0326-Condition 2
* Engine speed is greater than 2,000 RPM.
* Engine is running for greater than 1 s.
* The ECT is warmer than -40°C (-40°F).
* The IAT is warmer than -40°C (-40°F).
* The DTC runs continuously when the above conditions are met.
P06B6
* Engine speed is between 600 and 5,000 RPM.
* Engine is running greater than 5 s.
* The DTC runs continuously when the above conditions are met.
Conditions for Setting the DTC
P0324
The ECM detects that the knock sensor signal indicates an excessive engine knock or noise is present in at least a single cylinder.
P0326
* The ECM detects that the knock sensor signal indicates the sensor harness is connected, but the sensor is not properly bolted to the engine.
OR
* The ECM detects that the knock sensor signal indicates an excessive engine knock is present.
P06B6
The ECM has detected an internal knock sensor processor fault.
Action Taken When the DTC Sets
* DTCs P0324, P0326, and P06B6 are Type B DTCs.
* The ignition timing is retarded to reduce the potential of engine damaging spark knock.
Conditions for Clearing the DTC
DTCs P0324, P0326, and P06B6 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics [1][2]Electrical Diagrams
Connector End View Reference
Component Connector End Views Hybrid/EV Battery Pack X1
Description and Operation
Hybrid Modes of Operation Description Hybrid Modes of Operation Description
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References Programming and Relearning for scan tool information
Circuit/System Verification
1. Engine running, observe the DTC information with a scan tool. Verify DTC P0325, P0327, P0328, and P06B6 is not set.
• If DTC P0325, P0327, or P0328 is set with P06B6, refer to DTC P0325, P0327, or P0328 P0325 for further diagnosis.
• If DTC P06B6 is set, and no external knock sensor circuit issues exist, replace the K20 ECM.
2. Vehicle OFF, inspect for the following:
* The B68 knock sensor for physical damage. A sensor that is dropped or damaged may cause a DTC to set
* The sensor for proper installation. A sensor that is loose or not at the correct torque may cause a DTC to set. Refer to Fastener Tightening Specifications Specifications.
* The sensor mounting surface for burrs, casting flash, and foreign material
* The sensor must be clear of hoses, brackets, and engine electrical wiring
* Loose brackets
* Water pump and belt
* An engine mechanical condition-Refer to Symptoms - Engine Mechanical Symptoms - Engine Mechanical
• If a condition is found, repair as necessary.
3. If there is no mechanical condition, test or replace the B68 knock sensor.
4. Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the freeze frame/failure Records data.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Knock Sensor Replacement Service and Repair
* Control Module References Programming and Relearning for ECM replacement, setup, and programming