Fault-Tracing Information
Fault-tracing
Checking shift solenoid S1
- Ignition on.
- Activate solenoid S1.
Check the status for solenoid S1. The status must switch between OFF and ON.
The fault is permanent if the status does not change.
If the status switches it means that the fault was present previously but is not active now. There is an intermittent fault.
Continue - Checking the components and wiring
-------------------------------------------------
Verification
Verification
Hint: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reinstall the connectors, components etc.
- Ignition on.
- Activate solenoid S1 by clicking the symbol for VCT2000.
Read the status of solenoid S1. The status must switch between OFF and ON.
Is the function OK?
Yes - VERIFIED
No - VERIFICATION FAILED
------------------------
VERIFICATION FAILED - Fault-tracing information
VERIFIED - FAULT FOUND
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
Do you want to exit fault-tracing?
Yes - Exit fault-tracing
No - Attempt New Test
------------------------
Attempt New Test - Checking shift solenoid S1
-------------------------------------------------
Checking the components and wiring
- Ignition off.
- Open the transmission control system.
Check the cable. Check for an open-circuit. Check for a short-circuit to supply voltage.
Take readings between:
- Transmission connector #B5 and the connector for solenoid S1.
Hint: If no fault is found in the wiring check solenoid S1. See: Checking internal components of the transmission, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Checking Internal Components Of The Transmission
Remedy as necessary.
Other information
- Breakout box, connecting, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Connecting The Breakout Box, Transmission Control Module (TCM)
- Signal specification, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Signal Specification, Transmission Control Module (TCM)
- Transmission Control Unit Wiring Harness, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Service and Repair
- To access the transmission control system: Cover, control system, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Cover, Control System
- To access connector B/replace the solenoid: Transmission Control Unit Solenoids, B6304T4, TF-80SC AWD, B6324S5, TF-80SC AWD, B6324S5, TF-80SC, B6324S4, TF-80SC AWD, B6324S4, TF-80SC Transmission Control Unit Solenoids
- Checking wiring and terminals Checking Wiring And Terminals
Continue - Resetting the adaptation and oil quality counter
-------------------------------------------------
Resetting the adaptation and oil quality counter
Resetting adaptation
Resetting the adaptation and the counter for "Transmission oil, replace"
Hint: The transmission has torque-regulated, adaptive pressure regulation. The pressure regulator enables the transmission to regulate pressure during each shift to prevent hard shifting. Each shift is assessed by the transmission control module (TCM) and is stored in the internal memory. This makes it possible to compensate for transmission and clutch wear. It is important that the adaptation in the memory is reset so that the transmission works normally after the repair. Because the fluid was changed during the repair, the counter for transmission fluid change must also be reset. If the counter is not reset during draining/replacement, a diagnostic trouble code may be generated under the wrong conditions.
Note! This applies only if the transmission or one of the components in the transmission have been replaced.
- Ignition on.
Click on the VCT2000 symbol to reset the adaptation and counter.
Continue - DONE
------------------------
DONE - Verification
-------------------------------------------------