Part 3

Parking assistance, camera, rear




- Remove the panel.





- Remove the screws.
- Remove the panel.

Vehicles with 5 inch ICM display





Note! If there is no connection, replace the display.

Vehicles with 7 inch display




- Disconnect the connector, if applicable.
- use electrical tape to secure the connector in the existing cable.

Applies to all models





Note! The number of connectors, cables and cable ties can vary depending on the vehicle's equipment level.

- Unplug the connectors.





- Take the remaining cable harness and connect it to the control module.
- Route it under the member at the wheel housing, under the insulation and up to the door opening at the left-hand rear door.





- Remove the foam tape from the kit and split it in the centre.





- Remove the protective film from the foam tape.





- Apply the foam tape around the wiring to protect the cable from sharp edges.





- Pull out the B pillar panel at the lower edge until the two clips release.
- Continue to route the cable harness inside the B pillar panel and forwards in the car. Route the cable harness along the left-hand side, in front of the floor and insulation panels, up to the front edge of the door opening.

Only applies to left-hand drive vehicles




- Route the cable harness inside the floor and insulation panels, up on the A pillar slightly, and then at an angle upwards, between the A pillar and the end panel, towards the dashboard. Route the cable harness to the location for the screen in the dashboard.
- Place the cable harness so that it does not come into contact with sharp edges or moving parts under the dashboard.

Only applies to right-hand drive vehicles




- Take a piece of wire and insert it by the air ducts through the hole for the screen. Pull it out to the left, above the glove compartment and out through the left-hand end of the dashboard.
- Tape the connector on the cable to the screen by the wire.
- Pull the cable up to the location for the screen and out through the hole in the dashboard.

Applies to all vehicles




- Take a tie strap from the kit and secure the cable in the hole on the end as illustrated.

Only applies to left-hand drive cars




- Take two tie straps from the kit and clamp the cable at the existing cable harnesses inside the dashboard as illustrated.

Applies to all vehicles with 5 inch ICM display





Note! If there is no connection, replace the display.







Applies to all vehicles





Note! The number of connectors, cables and cable ties can vary depending on the vehicle's equipment level.

- Plug in the connector.

Applies to vehicles with 5 inch ICM display




- Plug in the connector.

Applies to vehicles with 7 inch display




- Plug in the connector.

Applies to all vehicles




- Reinstall the panel.
- Install the screws.
- Reinstall the detached components in reverse order.

Removal





- Remove the panel.





- Remove the screws.





- Remove the screws.

Applies to vehicles with manual transmissions










Cars with automatic transmissions









- Release the shift-lock function.

Applies to all vehicles




- Remove the panel.





1. Fold back the mat.
2. Unhook the cable harness clips.
3. Unplug the connector.










- Remove the covers.
- Remove the screws.

Vehicles with the 4C system




- Remove the panel.





- Unplug the connector.

Applies to all vehicles





Caution! Do not damage the hooks.

- Remove the panel.





- Remove the screws.










- Remove the cover plug.





- Install the switch.
- Reinstall the detached components in reverse order.





- Reconnect the battery negative lead






Warning! When the ignition is to be switched on for the first time after the battery has been disconnected, this must be done whilst by standing outside the vehicle, stretching your arm in and avoiding the working area for the airbags.

- Set the ignition switch to position II.





- Download software (application) for the accessory's function





Perform a function test as follows
- Engage reverse gear.
- The display is activated.
- Wait for the message "Update Environment" to appear on the screen.
- Follow the on-screen instructions.
- Switch off the ignition for at least 10 seconds.
- Turn the ignition on.
- The display is activated.
- Check that the support lines appear on the screen and that these react to steering wheel movements.