Fault Tracing Information
Fault-tracing
Fault-tracing information
Use the following information and general checks during fault-tracing.
Note! Check that the fuses are intact. For locations, see the instruction manual, cover for fuse box, fuse ratings or similar.
1. Check, if possible, relevant functions in the vehicle using buttons/controls/test drives to determine the status of the fault.
Note! If the vehicle does not show any of the given symptoms in the diagnostic trouble code information (DTC), this may mean that the fault is intermittent or that the control module is not detecting the fault at this moment.
2. Use the diagnostic trouble code's frozen values, status identifiers and counter to determine the operating conditions when the fault was detected, the fault's current status and any degree of intermittence of the fault.
Other information
- Description of frozen values Description of Frozen Values, IAM
- Description of status identifier Description of Status Identifier
- Description of counter Description of Counter
- Component location, audio module (AUD) Component Location, Audio Module (AUD)
Has the fault been remedied?
Yes - FAULT FOUND
No - Fault-tracing
-------------------------------------------------
Information
Fault-tracing information
In case of this defect, troubleshooting is not followed by verification.
The information can be displayed again or the fault-tracing for this fault can be interrupted.
Do you want to view the information again?
Yes - Attempt New Test
No - FAULT FOUND
------------------------
Attempt New Test - Fault-tracing information
-------------------------------------------------
Fault-tracing
Check if similar diagnostic trouble codes are stored in one or any of the other loudspeakers.
Are there similar DTCs in several loudspeakers?
Yes - Rectify in the following order
No - Rectify in the following order:
-------------------------------------------------
Rectify in the following order:
1. Check the connectors to the control module. Check for contact resistance, loose connections and oxidation.
2. Check the connector to the loudspeaker. Check for contact resistance, loose connections and oxidation.
3. Check relevant signals using wiring diagram, signal specification and breakout box.
4. Perform a visual inspection of the cable between the control module and loudspeaker. If necessary, install a new cable.
5. Check the loudspeaker.
Other information
- Component location, audio module (AUD) Component Location, Audio Module (AUD)
- Checking wiring and terminals Checking Wiring and Terminals
- Checking the supply voltage/ground terminal Component Tests and General Diagnostics
- Signal description, audio module (AUD) Signal Description, Audio Module (AUD)
- Joining cables Joining Cables
- Loudspeaker, side door front Loudspeaker, Front Side Door
- Loudspeaker side door, rear Loudspeaker, Rear Side Door
- Loudspeaker, dashboard Loudspeaker, Dashboard
Has the fault been remedied?
Yes - FAULT FOUND
No - Fault-tracing
-------------------------------------------------
Rectify in the following order:
1. Check the connector to the loudspeaker. Check for contact resistance, loose connections and oxidation.
2. Check the connectors to the control module. Check for contact resistance, loose connections and oxidation.
3. Check relevant signals using wiring diagram, signal specification and breakout box.
4. Perform a visual inspection of the cable between the control module and loudspeaker. If necessary, install a new cable.
5. Check the loudspeaker.
Other information
- Component location, audio module (AUD) Component Location, Audio Module (AUD)
- Checking wiring and terminals Checking Wiring and Terminals
- Checking the supply voltage/ground terminal Component Tests and General Diagnostics
- Signal description, audio module (AUD) Signal Description, Audio Module (AUD)
- Joining cables Joining Cables
- Loudspeaker, side door front Loudspeaker, Front Side Door
- Loudspeaker side door, rear Loudspeaker, Rear Side Door
- Loudspeaker, dashboard Loudspeaker, Dashboard
Has the fault been remedied?
Yes - FAULT FOUND
No - Fault-tracing
-------------------------------------------------
Fault-tracing
Rectify in the following order:
1. Use VIDA Vehicle communication. Read off the parameters, activate components and functions, carry out quick tests and checking routines for the diagnostic trouble codes to identify the fault.
2. Check relevant components according to Component specifications.
3. Remedy as necessary.
Note! More information is available in Design and function.
Continue - Fault-tracing information
-------------------------------------------------