Part 2

Parking assistance, front, chassis number 97000-















































INTRODUCTION
- Read through all of the instructions before starting installation.
- Notifications and warning texts are for your safety and to minimize the risk of something breaking during installation.
- Ensure that all tools stated in the instructions are available before starting installation.
- Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.
- In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.






Parking assistance, front, chassis number 97000-


Steps 58-82 apply to cars with external amplifier.




- Open the boot lid.
- Lift up the cargo compartment's divider.





- Remove the cover on each side of the divider.





- Unscrew the two nuts on each side of the divider four turns.





- Lower the divider slightly.
- Unscrew the third nut on each side of the divider four turns.





- Lower the divider completely.





- Detach the wire frame from the clip.





- Lock the two partition arms in place with a cable tie (for example) on the right and left side.





- Remove the divider by gripping the arms and lifting up.






Remove:
- the cover
- the spare wheel, if present.





- Remove the screw clip and load securing eyelet with its screw.

Applies to cars with a tool box
- Take the tools out of the toolbox.

Remove:
- the screw clip
- the screw
- the toolbox.





- Remove the three screws and the cargo lashing eyes from the floor.





- Remove the cover for the tailgate's stop, by prying, with a weatherstrip tool, between the cover and the sealing strip. Carry this out on both the left and right-hand sides.





- Remove the two light bulbs by pressing in the two catches at the top with a screwdriver.

Applies to cars with emergency opening handle in the cargo compartment




- Remove the emergency opening handle by pressing out the pin at the eye and unhook the wire.





- Remove the two screws from the sill moulding.





- Pull the sill moulding upwards until the clips release.
- Disconnect the large connector and remove the sill moulding.





- Remove the carpet in the cargo compartment.

Steps 75-82 apply to both right and left-hand drive cars. On right-hand drive cars, the procedure only needs to be carried out on the left-hand side in the cargo compartment.




- Remove the rubber stop on the roof's stop bracket on both the right and left-hand sides.





- Mark out the stop bracket for the roof in relation to the screw.
- Remove the screw and the roof's stop bracket.
- Carry out on both the left and right-hand sides.





- Remove the lock for the load divider by prying between the carpet and lock using a weatherstrip tool. Carry this out on both the right and left-hand sides. Remove the connector on the left-hand lock.





- Remove the screws and the cargo lashing eyes on both the right and left-hand sides.





- Remove the cover for the stop bracket on both the left and right-hand sides.





- Mark out the stop brackets for the roof in relation to the screw and the nut.
- Remove the screw, nut and the roof's stop braces.
- Carry out on both the left and right-hand sides.





- Detach the four clips on the side panels on both the right and left-hand sides.





- Remove the side panels on both the left and right-hand sides, by unhooking them from the stop lugs at the front edge and then pulling them outwards and upwards so that they release from the weatherstrip.






Note! Ensure that the cable harness does not lie against any moving components or too close to heat sources.

- Take the short cable harness from the kit.
- Remove the taped connector from the cable harness.
- Pull the end with the loose terminals in under the headlamp
- Continue to pull the cable harness (1) along the right-hand side of the car, under the expansion tank down to the cowl panel.
- Route the cable so that it is concealed and cannot be damaged or worn. Secure the cable harness using tie straps so that it does not move.





- Unscrew the clips holding the floor carpet.
- Fold aside the floor mat to access the bulkhead panel inside.
- Take care not to create folds in the carpet.