Parking Assist Switch: Service and Repair

Parking assistance, front, switch























INTRODUCTION
- Read through all of the instructions before starting installation.
- Notifications and warning texts are for your safety and to minimize the risk of something breaking during installation.
- Ensure that all tools stated in the instructions are available before starting installation.
- Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.
- In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.






Parking assistance, front, switch

Preparations





- Set the ignition key to position 0.

Note! Wait at least one minute before unplugging the connectors or removing other electrical equipment





- Remove the panel inside the center console. It is secured by four hidden clips.





- Remove the surround from around the display and media player. Use a small screwdriver and press in the catch in one of the surround's upper corners. Carefully bend loose the surround on the same side with a plastic weatherstrip tool.

Note! Do not damage the panel and dashboard.

- Do the same on the other side.

Hint: If the panel is difficult to remove, press the panel on both sides again and repeat the procedure starting at the other side.

- Fold the surround backwards. Remove by pulling upwards.





- Remove the infotainment control module (ICM). It is secured by two hidden clips. Disconnect the connectors.

Hint: Grip the control module with both hands. Pull the control module straight out of the center console.





- Detach the panel by pulling it carefully sideways.





- Fold up the tunnel console's armrest and remove the cover.





- Remove the screws.





- Remove the front storage compartment by prying it off at the front edge using a weatherstrip tool and lifting it out.





- Remove the two screws along the front edge of the tunnel console.


Illustration A




- Carefully lift the catches at the front edge of the tunnel console.

Hint: Use special tool: P/N 9995919.

Illustration B




- At the same time pull the console backwards approximately 20 mm.





- Remove the screws.






Applies to cars with manual gearbox
- Remove the gear selector lever boot from the center console. First pry it off at the front edge using a weatherstrip tool and then unhook it at the rear edge.






Remove:
- the two screws.
- the connector to the centre console at the rear.
- the centre console.





- Lift up the tunnel console and pull it back slightly.
- Unplug the big gray connector at the front.





- Lift out the tunnel console and turn it upside down.

Note! Protect hand brake and gear lever when removing and installing the tunnel console.

Installing the switch

Applies to vehicles with BLIS or Drive (not both)




- Release the catches holding the switch housing and lift out.





- Remove the blind cover plug by pulling it straight out.





- Install the switch from the kit.
- Reinstall the switch housing on the tunnel console.

Applies to vehicles with both BLIS and Drive, as well as vehicles without BLIS or Drive




- Remove the storage compartment from the tunnel console by releasing the catches.





- Take the switch housing, switch and blind cover plug from the kit. Install the switch (1) and the blind cover plug (2) in the switch housing.





- Install the switch housing on the tunnel console by first hooking it at the rear edge.





- Take the cable harness from the kit and connect the green connector to the switch housing.





- Secure the cable harness using four cable ties at the existing cable harness.





- Connect the connector (1) from the tunnel console's cable harness to the connector (2) on the prerouted cable harness.
- Take a piece of foam tape from the kit and wrap it around the connected connectors.

Finishing work

Applies to all models





Reinstall:
- the tunnel console and the large connector.
- the center console with its screws, two up and two down.
- gear lever gaiter, starting at the trailing edge.
- and slide the tunnel console forward so that the lugs secure it. At the same time align the floor carpet on the right and left-hand sides.
- the two screws at the front edge of the tunnel console.
- the cover at the parking brake.
- the panel at the parking brake.
- the two screws and the cover under the armrest.
- the ignition control module (ICM) with the connectors, screws and panel.
- front storage compartment inside of the center console.
- the panel inside the center console.
Applies to vehicles with both BLIS and Drive, as well as vehicles without BLIS or Drive
- Run the identification and configuration procedure for the accessory's function.
Applies to vehicles with BLIS or Drive (not both)
- Run the configuration procedure for the accessory's function.