Part 1
USB/Ipod Music Player, Bluetooth hands-free
INTRODUCTION
- NOTE! Read through the whole installation instruction before starting the work.
- The illustrations display the procedure in order of operation. The order of operation is repeated in the text
USB/Ipod Music Player, Bluetooth hands-free
Note! This installation instruction shows the installation of the USB/iPod adapter and Hands-free with Bluetooth on left-hand drive vehicles. When installing in right-hand drive vehicles the steps are performed on the opposite side and/or mirrored. The right-hand drive design is also shown with text and pictures when operations differ.When installing Velcro fasteners/tape the underlying surface must be kept at a temperature of at least +20° C (68°F).The cable between USB/iPod adapter and music player can be ordered for USB, iPod, or both.Wiring A is for vehicles with an internal amplifier that is located in the media player.Wiring B and C are for vehicles with an external amplifier, located on the left-hand side of the cargo compartment.Cars with Performance Sound have internal amplifier.Cars with the High Performance and Premium Sound audio systems have external amplifier.There may be components in the accessories kit that are not used for this installation.Place the manual for this accessory in a suitable place in the vehicle.
Preparations
- Turn the ignition key to position 0.
Note! Wait at least three minutes before unplugging the connectors or removing other electrical equipment.
- Open the glovebox.
Carefully pry off the panel at the rear of the centre console. Use a plastic weatherstrip tool. The panel is attached by two clips on each of the short sides.
- Pull the panel away downwards.
- Apply tape to the center console to protect it during removal and installation of the glove compartment.
- Remove the panel.
- Detach the clip holding the vent from the glove compartment.
- Remove the rubber mat from the glovebox.
- Remove the 5 x screws from the opening.
- Pull the glovebox straight back in the vehicle in order to release the hidden clips, 2 pcs, in the top edge.
- Remove the outer section of the glovebox.
- Unplug the connectors on the top.
- Remove the screws for the vent.
- Pull off the vent to the right and place to one side.
- Remove the clips at the rear edge of the soundproofing panel and remove it.
- Remove the surround around the display and media player:
Press in the catch at one of the surround's upper corners. Use a small screwdriver. Carefully pry off the surround on the same side. Use a plastic weatherstrip tool.
Note! Do not damage the panel and dashboard.
- Repeat the procedure for the other side and then fold the surround backwards into the vehicle. Pull the surround up until it detaches.
Hint: If the panel is difficult to remove, press the panel on both sides again and repeat the procedure starting at the other side.
- Remove the ignition control module (ICM). It is secured by hidden clips, 2 pcs.
Hint: Grip with both hands and pull.
- Disconnect the two connectors. Put the display to one side.
- Detach the hand brake panel by pulling it carefully sideways.
- Fold up the tunnel console's armrest and remove the cover at the bottom.
- Loosen the rear edge of the panel, it should not be completely removed.
- Remove the two screws.
Applies to all models
- Remove the two screws along the front edge of the tunnel console.
- Remove the front storage compartment by prying it off at the front edge using a weatherstrip tool and lifting it out.
- Carefully lift the catches at the front edge of the tunnel console.
Hint: Use special tool, P/N 9995919.
- Hold up the lock catch and at the same time slide the entire tunnel console back 20 mm, so that the two rear screws in the centre console are accessible.
- Remove the two screws.
Applies to cars with manual gearbox
- Remove the gear selector lever boot from the center console. First pry it off at the front edge using a weatherstrip tool and then unhook it at the rear edge.
- Remove the two screws holding the centre console's panel to the dashboard.
- Loosen the connector to the centre console at the rear.
- Remove the center console.
- Lift up the tunnel console and pull it back slightly.
- Unplug the big gray connector at the front.
- Lift out the console and turn it upside down
Note! Protect hand brake and gear lever when removing and installing the tunnel console.
- Unplug the connector of the 12V socket.
- Carefully bend loose the tunnel console's rear panel using a weatherstrip tool.
Installing the USB / iPOD cable
- Get the USB/iPod cable from the kit, insert the straight contact in the trailing edge of the tunnel console and into the storage compartment.
- Measure the length of the cable that is to be protrude from the bottom of the storage compartment.
- Clamp in the cable harness to the existing cable harness using cable ties.
- Push on the panel, ensuring the cable is not pinched.
- Reinstall the panel.
- Connect the connector to the 12V socket.
- Fold the carpet to the right of the center console.
Applies to cars with internal amplifier
- Remove cable harness (A) from the kit.
Applies to cars with external amplifier
- Remove cable harness (B) from the kit.
Applies to all cars
- Route the cables on the right-hand side of the centre console.
Note! The fibre cables must not be bent with a radius less than 25 mm (1"). Make sure the cables are routed so there is no risk of wear.
Applies to cars with internal amplifier
- Take the relay and two thick pieces of foam tape from the kit.
- Connect the connectors from cable harness A to the mute relay.
- Tape the foam tape pieces around the relay.
Applies to cars with internal amplifier
- Place the relay between the white metal bracket (1) and the climate unit, high up on the bulkhead partition.
- Take the adapter and 2 pieces of foam tape from the kit.
- Bend in the bracket at each end.