Part 2

USB/Ipod Music Player, Bluetooth handsfree (Continued)

Note! Position the cable so that it is not pinched when the sun visor mounting is refitted.




- Make a mark on the foam tape which is attached to the cable, 230 mm (9 1/16") from the microphone.
- Use a cable tie to fasten the cable at the mark at the existing connector.
- Install the three trim screws.




- Hold the microphone cable straight forward and refit the interior lighting.




- Clean the area on the microphone and headlining panel as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth.
Dry with care, do not rub.
- Allow to dry.

Note! In cases where the area is heavily soiled or treated with cockpit shine. First clean using a washing up detergent (FAIRY or similar).

- Remove the backing tape from one side of the Velcro strip and press it onto the microphone.




- Remove the remaining backing tape from the Velcro strip and press the microphone securely onto the ceiling panel as illustrated.

Note! Direct the microphone towards the driver.

- Feed in any cable excess.




- Route the cable to the A-pillar and onwards to the glove compartment.
- Take three small tie straps from the kit and secure the cable at the A-pillar as illustrated.
- Refit the sun visor mountings.
- Reinstall the A pillar panel and weatherstrip.

Installing the control panel




- Clean the area on the center console as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth.
Dry with care, do not rub.
- Allow to dry.

Note! In cases where the area is heavily soiled or treated with cockpit shine. First clean using a washing up detergent (FAIRY or similar).





Only applies to Right-hand vehicles
- Place the control panel cable in the groove as illustrated.




- Remove the protective film on the control panel and press in position as illustrated.




- Press the cable securely into the compartment that is in the joint between the front and rear side of the center console. Stop level with the lower edge of the display opening.




- Route the cable from the control panel on the right-hand side of the centre console.




- Reinstall the tunnel console, but do not slide it forward so far that it covers the rear screw holes for the centre console's panel.
- Plug in the connectors at the leading edge.

Note! Protect the hand brake and gear shift when fitting the tunnel console.




- Install the centre console, connect the green connector and fit the screws, two at the top and two on the rear edge.

Applies to cars with manual gearbox
- Install the gear selector boot in the center console starting at the rear edge.




- slide the tunnel console forward so that the locking lug secures it. At the same time, guide in the floor carpet on the left-hand side.

Reinstall:
- the two screws at the front edge of the tunnel console.
- the panel at the parking brake.




- Reinstall the screws




- File a slot at the rear of the storage compartment's bottom cover for the USB/iPod cable in the position as shown.




- Place the USB/iPod cable in the bottom cover's slot and pres it into place.





Reinstall:
- the ignition control module (ICM) with the connectors, screws and frame.
- front storage compartment inside of the center console.

Installing the control module




- Take the cable harness and control module from the kit. Connect the cable harness to the control module (1).
- Lock the catch (2).




- Get a thick foam tape from the kit and fasten it on the front of the control module. Fold up the foam tape around the corners and edges of the control module.




- Get three small pieces of foam tape from the kit and fasten these on the back of the control module.




- Detach the front sill molding by first pulling it backwards at the front edge and then straight up so that the clips release.




- Unscrew the clips holding the floor carpet.
- Fold aside the floor mat to access the bulkhead panel inside.

Note! Take care not to create folds in the carpet.




- Place the control module with the thick foam tape forward, against the bulkhead.




- Fold aside the cable harnesses (1) so that they do not end up between the control module and floor mat.
- Route the control module's cable harness under the cable harnesses (2) and on toward the tunnel console.
- Fold back the carpet.




- Connect the connectors for the Bluetooth system as illustrated:

Applies to cars with internal amplifier
1. 1. Connect cable harness A to the cable from the control module.

Applies to cars with external amplifier
1. 1. Connect cable harness B to the cable from the control module.

Applies to all models
1. 2. Connect the microphone
2. 3. Connect the control panel
- Take one of the cut pieces of foam tape and tape around the connectors.




- Place the connectors and the excess wiring inside the center console.
- Fold back the carpet.




- Take two large tie straps from the kit and secure the cable from the microphone on top of the collision pipe.

Applies to cars with external amplifier
- Also secure the cable harness B, that is to be later routed back to the external amplifier.

Steps 78-98 apply to cars with external amplifier




- Grasp the upper edge of the right-hand side cushion. Pull the side cushion forward so that the clip on the reverse releases.
- Slide the side cushion up. Remove the side cushion.
- Repeat the operation on the other side.




- Pull off the rubber strip at the rear of the opening for the right-hand rear door.
- Carefully pry off the lower panel on the C-post on the right-hand side. Carefully pry at the top edge. Use a plastic weatherstrip tool.
- Pull the panel on the C-post so that the two upper clips release. Then continue down until the last two clips release. Remove the panel on the C-post.




- Pull the top edge of the sill trim panel in the right-hand rear door inwards until the clips on the inside release. Then continue down and pull the panel upwards until the remaining two clips on the underside release.




- Pull off the rubber mouldings at the rear edge of the right-hand front door and at the front edge of the right-hand rear door. This releases the lower panel on the B-pillar.
- Pull the bottom edge of the lower panel on the B-pillar until the two bottom clips release.




- Fold the rear seat cushions and backrest forwards.





Applies to the V50
- Remove the cargo compartment carpet.




- Use a weatherstrip tool and pry up one corner of the sill trim panel so that the two clips on the short side release.
- Pull up the sill trim panel so the remaining six clips release. Remove the panel.
- Detach the rubber strip where it covers the left and right-hand side panel in the tailgate opening.




- Remove the screw.
- Pull the panel upwards so that the four clips on the inside release. Remove the panel.
- This must be carried out on the left-hand side on right-hand drive vehicles.




- Fold out the load securing eyelets.
- Insert a scriber with an angled tip into the holes in the top of the covers (1). Turn the scriber so that the tip engages the reverse of the cover. Pull the covers off.
- Remove the screws in the load securing eyelets.
- Remove the screw (2).
- Pull off the side panel at the top so that the two clips at the rear/bottom of the side window and the clip at the bottom of the D-post release.
- Disconnect the connector for the 12V socket, if present.
- This is carried out on the left-hand side on right-hand drive vehicles.





Applies to S40 (04-)
- Remove the cargo compartment carpet.




- Remove the upper floor support on the left and right-hand sides if applicable.




- Unscrew the two external clips at the front edge/bottom edge of the sill trim panel on the tailgate.
- Use a weatherstrip tool and pry up one corner of the sill trim panel so that the two clips in that end release.
- Pull up the sill trim panel at the other end so that the remaining two clips release. Remove the sill trim panel.





Illustrations A and B
- Remove the four clips (1), in illustration A, holding the side panel in the bodywork.
- Unhook the front edge of the parcel shelf panel at the mounting (2), in illustration A. Pull the side panel away from the parcel shelf panel and the panel on the C-post.
- Unhook the side panel from the mounting (3), in illustration B, on the underneath of the parcel shelf.
- Disconnect the connector for the 12V socket, if present.
- Unhook the side panel from the load securing eyelets (4), in illustration A. Remove the side panel.
- This is carried out on the left-hand side on right-hand drive vehicles.










Applies to the S40 and V50
- Route the cable (B) inside the floor carpets, the lower B-post panel and the insulation panels, back to the rear edge of the right-hand rear wheel arch. Route the cable along the existing cable harnesses in the cargo compartment.

Note! Ensure that the cable is positioned so that there is no risk of it catching or rubbing.





Applies to the S40 and V50 (not right-hand drive)
- Continue routing the cable harness to the amplifier.
- Position the cable harness at the existing cable harness to the side and at the rear edge of the cargo compartment, all the way from the right-hand wheel arch to the amplifier.
- Take a short tie strap from the kit and secure the cable harness at the existing cable harness.





Applies to the V50
- Remove the clips and the insulation panel.




- Disconnect the rear connector (1) on the amplifier.




- Remove cable harness (C) from the kit.
- Connect the cable harness to the amplifier as follows: Connector (1) which is disconnected from the amplifier is connected to the female connector (2) on the cable harness. Connector (3) on the cable harness is connected to the amplifier.
- Tape one section of the cut piece of foam tape around connectors (1) and (2).
- Secure the excess cable using one of the cut up parts of foam tape and two short tie straps, on the existing cable harness of the vehicle





Applies to the V50
- Reinstall the insulation panel on the left-hand side.

Applies to the S40 and V50
- Take the relay and 2 thick pieces of foam tape from the kit.
- Connect the connector from cable harness C and the routed cable harness connector to the relay.
- Fit 2 pieces of tape around the relay.




- Place the relay behind the existing cable harness.




- Reinstall the connectors to the rear section of the glove box. Note the color marking on the cable for the right-hand connector.

Reinstall:





Dashboard
- the lower vent.
- the sound proofing.
- the rear section of the glovebox by guiding it in diagonally inside the center console. Then straight forward. The rear section must be positioned on the outside of the remaining inner section.
- the clip for the vent on the glovebox.
- the panel on the dashboard end face.
- Remove the tape.
- the panel above the centre console. Check that the cable to the control panel is not pinched.

Passenger compartment
- the B-pillar panel.
- the sill trim panels.
- the C-pillar panel.
- the rubber strips in the door openings.
- side cushions.
- Position the backrest and seat cushions back into place.

Cargo compartment
- the side panels.
- the screws in the load securing eyelets. Tighten to 24 Nm (18 lbf.ft.) (applies to the V50).
- the sill trim panel for the tailgate.
- the upper floor support if applicable (applies to the S40).
- the cargo compartment carpet.




- Download the software for the accessory's function following the service information in VIDA
- Turn the ignition key to position I.
- Turn on the radio.
- Check that the control panel for Bluetooth lights up.
- Press the round button in the middle of the control panel. The radio should mute and a voice should be heard.
- Press the red handset button. The voice should now stop and the audio from the radio returns.