Part 3

Mobility Connection Package (Continued)

Applies to both right and left-hand drive vehicles




- Fold aside the floor mat on the left side of the center console.




- Disconnect the two connectors on the left-hand side of the gear selector assembly. Leave the male connectors in place.




- Take cable harness (A) from the kit. Connect the fiber-optic cable's connectors between those disconnected from the car's cable harness.

Note! Fibre-optic cables may not be bent with a radius less than 25 mm (1").




- Connect the two other connectors between the large connectors that were disconnected.

Applies to left-hand drive cars




- Insert the long fiber-optic cable (1) in front of the air duct and across the center console.
- Position the large loose connectors (2) and the excess of the fiber-optic cables (3) as illustrated.

Note! Fibre-optic cables may not be bent with a radius less than 25 mm (1").

- Fold back the carpet.

Applies to right-hand drive cars




- Position the large loose connectors' (1) and fibre-optic cable (2) excess as illustrated. Route the long fibre-optic cable (3) forward in the car.

Note! Fibre-optic cables may not be bent with a radius less than 25 mm (1").

- Fold back the carpet.

Applies to left-hand drive cars




- Take the cable harness from the kit. Insert the end with the two connectors from the front edge of the tunnel console's right-hand side inside the carpet and back along the inside of the tunnel console.

Applies to right-hand drive cars




- Take the cable harness from the kit. Insert the end with the two connectors from the front edge of the tunnel console's left-hand side inside the carpet and back along the inside of the tunnel console.

Applies to all models




- Lift up the tunnel console at the trailing edge and pull up the connector from the hole in the trailing edge of the storage compartment.




- Route the cable out from the storage compartment. Measure the length of the cable that is to protrude from the bottom of the storage compartment. Ensure that the cable does not chafe against sharp edges or become trapped when the removed components are reinstalled.




- Clamp the cable by the left bracket on the tunnel console with a cable tie when the cable length has been measured.
- Reinstall the centre console in its position.




- Take the control module and two pieces of foam tape from the kit.
- Bend the mountings in on the control module.

Illustrations A and B








- Remove the protective film on the foam tape and attach as illustrated.

Applies to left-hand drive cars




- Connect the two connectors to the control module.
- Clamp the USB/iPod cable at the eyelet on the control module using a cable tie.




- Fold the carpet to one side.
- Place the control module high up on the cowl panel and against the right-hand side of the centre console.
- Fold back the carpet.

Note! Do not damage the fibre optic cable.

Applies to right-hand drive cars




- Connect the two connectors to the control module.
- Clamp the USB/iPod cable at the eyelet on the control module using a cable tie.




- Fold the carpet to one side.




- Place the control module against the firewall under the cable harness. Secure the control module using a cable tie in the cable harness for the fuse box.




- Route the fiber-optic cable in a loop in front of the climate control unit.

Applies to all models




- Tighten down the tunnel console with the four screws. Make sure that the cable from the USB/iPod adapter does not get caught in the rear bracket when the screws are tightened.
- Reinstall the panels and screws at the rear edge of the tunnel console.

Illustrations A and B




Image A shows car without telephone




Illustration B shows car with telephone
- Mark out and drill holes at the rear edge of the storage compartment mat, use a -6 mm (1/4") drill bit.
- Cut the mat to the edge of the hole.
- Clean out the hole so that the cable has room.
- Reinstall the rubber mat in the bottom of the storage compartment.




- Remove the panel around the display and media player. Use a small screwdriver and press in the catch in one of the panel's upper corners. Carefully bend loose the radio panel on the same side with a plastic pry tool.
- Carry out the same procedure on the other side. Then fold the radio panel backward in the vehicle.
- Pull up the radio panel until it detaches.

Hint: If there is difficulty removing the panel, press the panel back into place on both sides and start the removal procedure again. Start from the opposite side to before.




- Remove the gear lever panel by carefully prizing it away starting at the rear edge and then continuing forward. It is fitted with six catches underneath.

Applies to cars with manual gearbox




- Remove the gear lever panel from the gaiter by first pressing in the four catches at the sides, and then pull the panel up.




- Remove the covers and screws in the rear edge of the upper panel section of the centre console, remove the screws on the rear of the panel and then remove the remaining screws on the top, ten in total.




- Remove the edge clip with cable from the lower section of the centre console.




- Carefully angle up the upper section of the centre console at the front edge so that the edge clip for the large cable harness on the left-hand side of the centre console is accessible.
- Detach the clip with cable harness from its holder.

Note! Do not damage the fibre optic cables and other cables.




- Tilt the upper section of the centre console a little more to access the four connectors at the rear of the climate unit.
- Unplug the connectors. The connector (1) has a catch on the rear in toward the upper section.




- Remove the panel by moving it backward at the front edge and then lifting it out from the rear edge of the tunnel console.




- Remove the two screws from the media player.




- Pull out the media player completely and remove the connectors.




- Clean the area on the dashboard as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth. Wipe dry carefully, do not rub.
- Allow to dry.

Note! In cases where the area is heavily soiled or treated with cockpit shine, first clean using a washing up detergent.




- Remove a long piece of foam tape from the kit and cut it in the centre.
- Tape the piece of foam tape around the cable to the control panel.

Applies to left-hand drive cars




- Position the keypad cable in the groove as illustrated.




- Remove the protective film on the control panel and press securely.




- Carefully push the cable harness in between the panels using a weatherstrip tool. Angle/pull out the upper section of the centre console to create a larger gap between the dashboard and tunnel console, and to make it easier to press the cable completely inside the tunnel console's side wall (1).





Note! Make sure the cable harness runs free of the panel's guides.




- Secure the control panel's cable using a cable tie in the existing cable harness.




- Route the cable through to the other side.




- Remove the right end panel of the dashboard.




- Detach the moulding on the front edge of the door opening.