Part 3

USB/Ipod Music Player, Bluetooth hands-free (Continued)

Steps 94 up to and including 101 apply to both right and left-hand drive cars. On right-hand drive cars, the procedure only needs to be carried out on the left-hand side in the cargo compartment.
- Remove the rubber stop on the roof's stop bracket on both the right and left-hand sides.




- Mark out the stop bracket for the roof in relation to the screw.
- Remove the screw and the roof's stop bracket.
- Carry out on both the left and right-hand sides.




- Remove the lock for the load divider by prying between the carpet and lock using a weatherstrip tool. Carry this out on both the right and left-hand sides. Remove the connector on the left-hand lock.




- Remove the screws and the cargo lashing eyes on both the right and left-hand sides.




- Remove the cover for the stop bracket on both the left and right-hand sides.




- Mark out the stop brackets for the roof in relation to the screw and the nut.
- Remove the screw, nut and the roof's stop braces.
- Carry out on both the left and right-hand sides.




- Detach the four clips on the side panels on both the right and left-hand sides.




- Remove the side panels on both the left and right-hand sides, by unhooking them from the stop lugs at the front edge and then pulling them outwards and upwards so that they release from the weatherstrip.




- Remove the center section of the rear seat backrest.




- Detach the two rear backrests by gripping them at the top and pulling forward/up.




- Remove the sill trim panel at the right-hand front door. First pull off the front edge of the sill trim panel so that the clip releases. Then continue backward until the remaining clips on the underside have released.




- Remove the screw and the rear sill trim panel.




- Route the cable between the floor carpet and the sill. Position the cable so that it is not trapped or damaged.




- Route the cable along the existing cable harness backwards and into the cargo compartment.




- Route the cables along the existing cable harnesses in the cargo compartment.





Does not apply to right-hand drive cars.
- Route the cable harness along the existing cable harnesses in the cargo compartment, away to the amplifier.
- Secure with 3 x small tie-straps.





Applies to cars with subwoofer amplifier
- Remove the subwoofer amplifier by removing the screws and unplugging the connectors.




- Detach the cable harness from the weld screw.




- Remove the screw and the two nuts.
- Lift the amplifier forward.




- Remove the green connector.




- Remove cable harness C from the kit.
- Route the white connector for the cable harness through the hole from the compartment behind the amplifier and out to the cargo compartment.




- Connect cable harness C to the amplifier as follows:
1. 1. Connector (1) that was disconnected from the amplifier is connected to the connector (2) on cable harness C.
2. 2. Connector (3) is connected to the amplifier.
- Tape one piece of the cut thin foam tape around the connectors (1) and (2).




- Reinstall the amplifier with nuts and screws, tightening torque 10 Nm (7 ftlb.).
- Reinstall the cable harness on the weld screw.
- Reinstall any amplifiers for subwoofers.




- Take the relay and two pieces of thick foam tape from the kit.
- Connect the connector from cable harness B and the newly routed cable harness connector to the relay.
- Fit the pieces of tape around the relay.




- Place the relay on the existing cable harness and secure it using a large tie-strap. Place any cable excess in front of the amplifier.




- Reinstall the connectors to the rear section of the glove box. Note the color marking on the cable for the right-hand connector.

Reinstall:





Dashboard
- the lower vent.
- the rear section of the glovebox by guiding it in diagonally inside the center console. Then straight forward. The rear section must be positioned on the outside of the remaining inner section.
- the clip in the air vent on the end face of the dashboard.
- the panel on the dashboard end face.
- Remove the tape.
- the panel above the center console. Check that the cable to the control panel is not pinched.

Passenger compartment
- the sill trim panels.
- the rubber strips in the door openings.
- Position the backrest and seat cushions back into place.

Cargo compartment
- the side panels (Check that the sealing strip is on the outside of the panel).
- stop and mounting brackets.
- the cargo compartment carpet.
- boot lid's sill plate with lighting.
- any emergency opener.
- the cover for the cargo compartment stop.
- the screws in the load securing eyelets. Tighten to 24 Nm (18 ftlb.).
- the toolbox.
- the spare wheel, if present.
- the divider, remove the tie-straps, tighten the nuts to 10Nm (7.3 ftlb.).




- Download the software for the accessory's function
- Turn the ignition key to position I.
- Turn on the radio.
- Check that the control panel for Bluetooth lights up.
- Press the round button in the middle of the control panel. The radio should mute and a voice should be heard.
- Press the red handset button. The voice should now stop and the audio from the radio returns.