Part 2

USB/Ipod Music Player, Bluetooth hands-free (Continued)

Note! In cases where the area is heavily soiled or treated with cockpit shine. First clean using a washing up detergent (FAIRY or similar).

- Remove the backing tape from one side of the Velcro strip and press it onto the microphone.




- Remove the remaining protective film from the Velcro strip and press the microphone securely onto the ceiling panel as illustrated.

Note! Direct the microphone towards the driver.




- Route the microphone cable on the top side of the ceiling panel. The microphone cable must point inwards so that it is not visible.




- Pull the cable down along the A-pillar to the dashboard.
- Cut two, 100x50 mm (4x2") pieces of foam tape in the middle.
- Secure the cable to the A-pillar using foam tape.




- Reinstall the A-pillar panel.




- Reinstall the sealing strip and ensure that it ends up on the outside of the panel.




- Secure the microphone cable using a small tie-strap.

Installing the control panel




- Clean the area on the center console as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth.
Dry with care, do not rub.
- Allow to dry.

Note! In cases where the area is heavily soiled or treated with cockpit shine. First clean using a washing up detergent (FAIRY or similar).





Only applies to Right-hand vehicles
- Place the control panel cable in the groove as illustrated.




- Remove the protective film on the control panel and press in position as illustrated.




- Press the cable securely into the compartment that is in the joint between the front and rear side of the center console. Stop level with the lower edge of the display opening.




- Route the cable from the control panel on the right-hand side of the center console.




- Reinstall the tunnel console, but do not slide it forward so far that it covers the rear screw holes for the center console's panel.
- Plug in the connectors at the leading edge.

Note! Protect the hand brake and gear shift when fitting the tunnel console.




- Install the center console, connect the green connector and fit the screws, two at the top and two on the rear edge.

Applies to cars with manual gearbox
- Install the gear selector boot in the center console starting at the rear edge.




- slide the tunnel console forward so that the locking lug secures it. At the same time, guide in the floor carpet on the left-hand side.

Reinstall:
- the two screws at the front edge of the tunnel console.
- the panel at the parking brake.
- rear tunnel compartment with its screws and cup holder.




- Reinstall the screws




- File a slot at the rear of the storage compartment's bottom cover for the USB/iPod cable in the position as shown.




- Place the USB/iPod cable in the bottom cover's slot and pres it into place.





Reinstall:
- the ignition control module (ICM) with the connectors, screws and frame.
- front storage compartment inside of the center console.

Installing the control module




- Take the cable harness and control module from the kit. Connect the cable harness to the control module (1).
- Lock the catch (2).




- Get a thick foam tape from the kit and fasten it on the front of the control module. Fold up the foam tape around the corners and edges of the control module.




- Get three small pieces of foam tape from the kit and fasten these on the back of the control module.




- Detach the front sill molding by first pulling it backwards at the front edge and then straight up so that the clips release.




- Unscrew the clips holding the floor carpet.
- Fold aside the floor mat to access the bulkhead panel inside.

Note! Take care not to create folds in the carpet.




- Place the control module with the thick foam tape forward, against the bulkhead.




- Fold aside the cable harnesses (1) so that they do not end up between the control module and floor mat.
- Route the control module's cable harness under the cable harnesses (2) and on toward the tunnel console.
- Fold back the carpet.




- Connect the connectors for the Bluetooth system as illustrated:

Applies to cars with internal amplifier
1. 1. Connect cable harness A to the cable from the control module.

Applies to cars with external amplifier
1. 1. Connect cable harness B to the cable from the control module.

Applies to all models
1. 2. Connect the microphone
2. 3. Connect the control panel
- Take one of the cut pieces of foam tape and tape around the connectors.




- Place the connectors and the excess wiring inside the center console.
- Fold back the carpet.




- Take two large tie straps from the kit and secure the cable from the microphone on top of the collision pipe.

Applies to cars with external amplifier
- Also secure the cable harness B, that is to be later routed back to the external amplifier.

Steps 77-118 apply to cars with external amplifier




- Open the boot lid.
- Lift up the cargo compartment's divider.




- Remove the covers on each side of the divider.




- Unscrew the two nuts on each side of the divider four turns.




- Lower the divider slightly.
- Unscrew the third nut on each side of the divider four turns.




- Lower the divider completely.




- Detach the wire frame from the clip.




- Lock the two partition arms in place with a cable tie (for example) on the right and left side.




- Remove the divider by gripping the arms and lifting up.





Remove:
- the cover.
- the spare wheel, if present.




- Remove the screw clip and load securing eyelet with its screw.

Applies to cars with a tool box
- Take the tools out of the toolbox.

Remove:
- the screw clip.
- the screw.
- the toolbox.




- Remove the three screws and the cargo lashing eyes from the floor.




- Remove the cover for the tailgate's stop, by prying, with a weatherstrip tool, between the cover and the sealing strip. Carry this out on both the left and right-hand sides.

Note! On right-hand drive vehicle's, the procedure only needs to be carried out on the left-hand side.




- Remove the two light bulbs by pressing in the two catches at the top with a screwdriver.





Applies to cars with emergency opening handle in the cargo compartment
- Remove the emergency opening handle by pressing out the pin at the eye and unhook the wire.




- Remove the two screws in the sill moulding.




- Pull the sill molding up until the clips release. Remove the large connector and remove the sill molding.




- Remove the carpet in the cargo compartment.