Brake Control Module (BCM)

VOLVO BCM CODE DESCRIPTIONS
BCM-0010 Left front wheel sensor. Signal missing
BCM-0011 Left front wheel sensor. Faulty signal
BCM-0012 Left front wheel sensor. Faulty signal
BCM-0020 Right front wheel sensor. Signal missing
BCM-0021 Right front wheel sensor. Faulty signal
BCM-0022 Right front wheel sensor. Faulty signal
BCM-0030 Left rear wheel sensor. Signal missing
BCM-0031 Left rear wheel sensor. Faulty signal
BCM-0032 Left rear wheel sensor. Faulty signal
BCM-0040 Right rear wheel sensor. Signal missing
BCM-0041 Right rear wheel sensor. Faulty signal
BCM-0042 Right rear wheel sensor. Faulty signal
BCM-0050 Control module. Faulty signal
BCM-0052 Control module. Internal fault
BCM-0057 Power supply. Voltage too low
BCM-0058 Power supply. Voltage too high
BCM-0061 Brake discs. Temperature too high
BCM-0065 Stop lamp switch. Faulty signal
BCM-0068 Sensor power supply. Faulty signal
BCM-0070 Power supply for the pump motor. Faulty signal
BCM-0071 Pump motor. Signal missing
BCM-0072 Pump motor. Mechanical fault
BCM-0074 Hydraulic valves. Faulty signal
BCM-0076 Control module. Faulty configuration
BCM-0080 Lateral accelerometer. Incorrect offset value
BCM-0081 Accelerometer. Incorrect offset value
BCM-0082 Yaw rate sensor. Incorrect offset value
BCM-0083 Angle of lean sensor. Incorrect offset value
BCM-0090 Lateral accelerometer. Faulty signal
BCM-0091 Accelerometer. Faulty signal
BCM-0092 Yaw rate sensor. Faulty signal
BCM-0093 Angle of lean sensor. Faulty signal
BCM-0094 Communication between control modules. Communication problems with Active on Demand Coupling
BCM-0095 Communication between control modules. Communication problems with Active on Demand Coupling
BCM-0097 Communication between control modules. Communication problems with the central electronic module (CEM)
BCM-0100 Communication between control modules. Communication problems with the engine control module (ECM)
BCM-0101 Communication between control modules. Communication problems with the engine control module (ECM)
BCM-0103 Pedal position sensor. Faulty signal
BCM-0106 Steering wheel or wheel alignment. Incorrect steering wheel or wheel alignment
BCM-0108 Communication between control modules. Communication with the steering angle sensor. Control module not initiated
BCM-0109 Communication between control modules. Communication with the steering angle sensor. Internal fault
BCM-0111 Communication between control modules. Check of the steering angle sensor tolerances has not been run
BCM-0112 Active yaw control sensor. Sensor not calibrated
BCM-0113 Back-up (reversing) signal. Signal missing
BCM-0114 Communication with the active yaw control sensor. Signal missing
BCM-0115 Communication between control modules. Communication with the steering angle sensor. Signal missing
BCM-0116 Communication with the active yaw control sensor. Communication problems
BCM-0117 Communication with the active yaw control sensor. An incorrect active yaw control sensor had been installed
BCM-0118 Power supply for the active yaw control sensor. Voltage too high
BCM-0119 Power supply for the active yaw control sensor. Voltage too low
BCM-0121 Yaw rate sensor. Signal outside its permitted range
BCM-0123 Active yaw control sensor. Internal fault
BCM-0125 Lateral accelerometer. Signal outside its permitted range
BCM-0127 Angle of lean sensor. Signal outside its permitted range
BCM-0129 Accelerometer. Signal outside its permitted range
BCM-0130 Brake pressure sensor 1. Signal too low
BCM-0133 Brake pressure sensor 2. Signal too low
BCM-0136 Brake pressure sensor 1 and 2. Signal outside its permitted range
BCM-0138 Power supply for the active yaw control sensor. Faulty voltage
BCM-0139 Pressure build-up valve, power brake booster. Signal outside its permitted range
BCM-0140 Pedal pressure sensor. Signal outside its permitted range
BCM-0145 Stability control. Too long stability control
BCM-0146 Factory test, dynamic stability and traction control (DSTC). Test cycle not approved
BCM-0147 Pedal position sensor. Signal outside its permitted range
BCM-0148 Communication between control modules. Faulty configuration ID
BCM-0150 Stop lamp switch. Signal outside its permitted range
BCM-0151 Control module. Internal memory fault
BCM-A030 Communication between control modules. Steering angle sensor. Initialization check not run
BCM-A031 Communication between control modules. Steering angle sensor. Tolerance check not run
BCM-A032 Stability function. Too long stability control
BCM-E000 Control module communication. Faulty communication
BCM-E003 Configuration fault. Faulty configuration
BCM-XXXX Unknown diagnostic trouble code (DTC) for the current control module version