Part 4

Hands free unit for carphone (Continued)

Applies to all, removing components in the cargo compartment




- Lift up the cargo compartment divider.




- Remove the covers on each side of the divider.




- Unscrew the two nuts on each side of the divider four turns.




- Lower the divider slightly.
- Unscrew the third nut on each side of the divider four turns.




- Lower the divider completely.




- Detach the wire frame from the clip.




- Lock the two partition arms in place with a cable tie (for example) on the right and left side.




- Remove the partition by taking hold of the arms and lifting upward.





Remove:
- the cover on the tool box
- the spare wheel, if in place.




- Take the tools out of the toolbox.

Remove:
- the clip
- the screw
- the toolbox.




- Remove the three screws and the cargo lashing eyes from the floor.




- Remove the cover from the boot lid stop. Use a weatherstrip tool to pry between the cover and the stop to release the catches.
- If the car has an external amplifier, do the same on the left side.




- Remove the two light bulbs by pressing in the two catches at the top with a screwdriver.





For cars with emergency release handle in cargo compartment
- Remove the emergency opening handle by pressing out the pin at the eye and unhook the wire.




- Remove the two screws in the sill moulding.




- Remove the sill protection by pulling it up until the clip releases. Fold the sill protection to the side.




- Remove the cargo compartment carpeting.




- Remove the rubber stop on the roof's stop bracket on the right side.
- If the car has an external amplifier, do the same on the left side.




- Mark out the stop bracket for the roof in relation to the screw.
- Remove the screw and the roof's stop bracket on the right side.
- If the car has an external amplifier, do the same on the left side.




- Remove the load divider lock on the right side by using a weatherstrip tool to pry between the carpet and lock.
- If the car has an external amplifier, do the same on the left side.




- Remove the screw and the cargo lashing eye on the right side.




- Remove the stop bracket cover on the right side.
- If the car has an external amplifier, do the same on the left side.




- Mark out the stop braces for the roof in relation to the screws and nuts on the right side.
- Remove the screw, nut and the roof's stop braces.
- If the car has an external amplifier, do the same on the left side.




- Detach the four clips on the side panel on the right side.
- If the car has an external amplifier, do the same on the left side.




- Remove the side panel by unhooking it from the stop lug at the front edge and the pulling outward and upward so that it releases from the sealing strip.
- If the car has an external amplifier, do the same on the left side.




- Remove the center section of the rear seat backrest.




- Detach the two rear backrests by gripping them at the top and pulling forward/up.




- Detach the seat cushion by gripping the front edge and pulling it forward.




- Remove the screw and the rear sill trim panel.




- Route the cable between the floor carpet and the sill. Position the cable so that it is not trapped or damaged.




- Route the cable along the existing cable harness backwards and into the cargo compartment.




- Route the cables along the existing cable harnesses in the cargo compartment.

Caution! Ensure that the cable is positioned so that there is no risk of it catching or rubbing.

Connecting to the accessory electronic module (AEM)




- Pull the accessory electronic module (AEM) away from its console.




- Unplug the small connector (1) on the accessory electronic module (AEM).
- Unplug the large connector (1) on the accessory electronic module (AEM). Press in the catch (2). Pull the black locking handle (3) in the direction of the arrow until a click is heard.
- Disconnect the connector from the accessory electronic module.




- Remove the black catch holding the black switch in place in the connector by pulling in the direction of the arrow.
- Remove the black switch by inserting a pointed object in the hole on the other shorter side. Press the switch out.




- Cut open approx. 12 cm from the cable sheath on the routed cable harness and take the grey/white cable.
- Connect the grey/white (GR/W) cable to position 11 in the accessory electronic module (AEM) connector.

Note! The numerical markings on the top and bottom of the black terminal pin are extremely small, so be careful when installing the cable.

- Reinstall the black switch in the connector. Lock into place using the catch.
- Press the connector into the Accessory Electronic module. Secure using the black locking handle.
- Reinstall the accessory electronic module (AEM) in its bracket.





Applies to cars with external amplifier
- Route the cable harness along the existing cable harnesses in the cargo compartment, away to the amplifier.





Applies to cars with subwoofer amplifier
- Remove the subwoofer amplifier by removing the screws and unplugging the connectors.





Applies to cars with external amplifier
- Detach the cable harness from the weld screw.





Applies to cars with external amplifier
- Remove the screw and the two nuts.
- Lift the amplifier forward.





Applies to cars with external amplifier
- Remove the green connector.





Applies to cars with external amplifier
- Thread the two adapter cable connectors through the hole in the cargo compartment and on behind the amplifier.





Applies to cars with external amplifier
- Connect the adapter cable to the amplifier as follows:
- plug connector (1) (disconnected from the amplifier) into the female connector (2) on the adapter cable
- plug connector (3) into the amplifier
- To prevent rattling, wind foam plastic around the detached connector.





Applies to cars with external amplifier
- Secure the cables at the lead-through with a tie strap. Route the cables on along the car's normal cable harness.
- Reinstall the amplifier with nuts and screws, tightening torque 10 Nm (7 ftlb.).
- Reinstall the cable harness on the weld screw.

Supplementary work




- Reinstall the connectors to the rear section of the glovebox. Note the color marking on the cable for the right connector.

Passenger compartment




- Reinstall the lower vent.
- Reinstall the front section of the glove compartment.
- Reinstall the rear section of the glovebox by guiding it in diagonally inside the center console and then straight forward. The rear section must be positioned on the outside of the remaining inner section.
- Reinstall the clips in the vent on the ends of the dashboard.
- Reinstall the panel on the ends of the dashboard.
- Reinstall the center console and connect the dashboard environment panel.
- Reinstall the panel on the center console rear edge.
- Connect and reinstall the display unit.
- Press the surround for the display into place.

Reinstall:
- the sound barrier
- the temperature sensor
- the panel inside the center console
- the sill trim panels on the right-hand side
- the backrests and seat cushion.

Cargo compartment

Reinstall:
- the side panels
- the stops and attaching braces
- the luggage compartment mat
- the sill panel with lighting
- emergency opener, if present
- the stop for the trunk lid
- the cargo lashing eyes with screws, tightening torque: 24 Nm (17 ftlb.)
- the tool box
- the divider; remove the cable ties.




- Reconnect the battery negative lead
- Programme the software in accordance with the service information in VIDA.