Part 2

Hands free unit for carphone (Continued)

Phone module connection

Applies to cars with external amplifier
- Take the long cable harness from the kit.
- Route the end with the small white connector and the brown (BN) single cable under the carpet near the right-hand door sill. Pull it up along the front edge of the fuse holder (CEM) and position as illustrated.
- Take the phone module and connect the adapter cable (1).
- Connect the routed cable harnesses,
- the cable (2) for the microphone
- the cable (3) for the power supply and accessory electronic module (AEM)
- the cable (4) for the telephone holder
- The brown (BN) single cable is connected to the fuse holder (CEM) under the dashboard as per step 43.

Applies to cars with external amplifier
- Wrap the control module with foam tape from the kit to prevent rattling.

Applies to cars with external amplifier
- Remove the 14-pin connector from the fuse holder by pressing in the catch on the front of the connector.

Applies to cars with external amplifier
- Press out the connector's secondary catch by first pressing in the lock tab on the inside (A, B) and then press out (C) in one side of the connector.

Applies to cars with external amplifier
- Turn the connector over and push out the other end with the four small holes on the opposite side of the connector.

Applies to cars with external amplifier
- Connect the routed brown (BN) cable to position 9 in the removed connector.
- Secure the auxiliary locking mechanism on the connector and reinstall it in the fuse holder.

Applies to cars with internal amplifier
- Take the long cable harness from the kit.
- Route the end with the small white connector under the carpet at the right-hand door sill. Route it up in the front edge of the fuse holder (CEM), route it forward and locate it as illustrated.
- Take the phone module and connect the adapter cable (1).
- Connect the routed cable harnesses,
- The cable (2) for the microphone
- the cable (3) for the power supply and accessory electronic module (AEM)
- the cable (4) for the telephone holder

Applies to cars with internal amplifier
- Wrap the control module with foam tape from the kit to prevent rattling.

Applies to cars with internal amplifier
- Connect the grey connector (1) in the routed cable harness to the corresponding socket in the media player.
- Connect the grey connector (2) in the routed cable harness to the grey connector (3) which was detached from the media player.
- Plug the remaining connectors which where detached into the media player.
- Reinstall the media player and secure it.

Applies to all models

- Place the newly connected phone module as far in against the left-hand side of the bulkhead as possible. Position the module so that it does not loosen or run the risk of becoming trapped by the inner section of the glovebox when the glovebox is reinstalled.

Preparations for right-hand drive car

- Turn the ignition key to position 0.
- Disconnect the battery negative lead.

Note! Wait at least three minutes before unplugging the connectors or removing other electrical equipment.

- Position the steering wheel in its lowest and rearmost position.
- Remove the two screws from the surround for the combined instrument panel.

- Pull off the surround starting at the lower edge and then at the upper edge. The surround is secured by a clip at each side of the lower edge. Place the surround to one side.

- Carefully pry off the panel at the rear edge of the center console. Use a weatherstrip tool. The panel is secured by a catch on each of the short sides.
- Move the panel to the side to access the two screws underneath.

- Remove the two screws.

- Open the glovebox.
- Carefully pry off the panel inside the center console. Use a plastic weatherstrip tool. The panel is secured by two clips on each of the short sides.
- Pull the panel away downwards.

- Remove the temperature sensor by pulling it forward so that it detaches from its holder.

- Detach the surround around the display and the media player: Press in the catch at the edge of the media player cover. Use a small screwdriver. Carefully pry off the surround at the corner. Use a plastic weatherstrip tool.

Note! Do not damage the panel and dashboard.

Repeat the operation on the other side.

Hint: If the other side does not detach, press the detached side into position again and repeat the procedure, beginning from the other side.

- Fold the surround backwards. Remove by pulling upwards.

- Press out the display module (1) from the reverse of the center console. Use both hands and press straight back.
- Disconnect the two connectors. Put the display to one side.

- Remove the two screws holding the center console to the dashboard.
- Remove the connector on the reverse of the dashboard environment panel.
- Remove the center console from the dashboard and tunnel console.

- Remove the two screws from the bottom of the media player.
- Pull out the media player and detach the connectors on the rear side.

Note! Note how the wiring is packed on the reverse. The fibre optic cables are easily damaged and must not be bent to a radius less than 25 mm (1").

- Remove the panel on the right-hand and left-hand ends of the dashboard. Carefully pry off the panel until the three clips release. Use a weatherstrip tool.

Note! Do not damage the dashboard.

- Remove the sill trim panel. First pull it away at the front so that the clips there release. Then continue backwards until the remaining clips on the underside have released.

- Remove the clip holding the nozzle for the air duct on the right-hand and left-hand sides.

- Remove the five screws in the opening to the glovebox.

- Remove the glovebox front section by pulling it back until the two clips in the upper edge release. Unplug the two connectors on the top.

- Remove the screw for the vent on the left-hand side. Pull off the vent to the left. Place to one side.

- Remove the four screws for the inner section of the glovebox. Pull out. Place it to one side. If a DVD reader is installed, detach the connectors on the back side.