Antenna Amplifier, Multipath "Diversity"

Antenna amplifier, multipath "Diversity"
























Antenna amplifier, multipath "Diversity"

Note! On certain models the electrical cable for the antenna amplifier may be pre-routed. Check if a black cable has been routed under the right-hand side tail lamp. Check if there are two black electrical cables routed to the two-pin connector on the right-hand side of the rear edge on the radio.
- If there is no black electrical cable pre-routed under the right-hand side tail lamp, carry out points Antenna amplifier, multipath "Diversity".
- If a black electrical cable is pre-routed under the right-hand tail lamp and only one black electrical cable has been routed to the two-pin connector on the right-hand side of the rear edge on the radio, carry out points Antenna amplifier, multipath "Diversity" and secure the old cable
- If there are two black electrical cables in the two-pin connector on the right-hand side of the rear edge on the radio but no black electrical cable is pre-routed under the right-hand tail lamp, carry out points Antenna amplifier, multipath "Diversity". Remove the right-hand (looking towards the front of the car) of the two cables from the connector. Clamp this cable to secure it
- If there are two black electrical cables in the two-pin connector on the right-hand side of the rear edge on the radio and a black electrical cable is pre-routed under the right-hand tail lamp, carry out point Antenna amplifier, multipath "Diversity".

Interior preparations




- Move the right front seat to the rearmost position
- Turn the ignition key to position O
- Cars with manual gearboxes: Remove the ignition key.

Note! Wait at least five minutes before disassembling the connectors or removing other electrical equipment.

- Disconnect the battery negative lead.

Illustration A applies to the S60 and the V70




- Remove the panel in front of the gear selector lever. Pry off the panel using a weatherstrip tool
- Move the gear selector lever to its rearmost position.

Illustration B applies to the S80




- Remove the panel (1) with the boot. Carefully pry the panel with a weatherstrip tool.

Illustration A applies to the S60 and the V70




- Remove the two screws from the dashboard environment panel.

Illustration B applies to the S80




- Shift the gear selector lever into rearmost position
- Pull the panel (1) with the boot backward as far as possible
- Remove the screws (2) from the dashboard environment panel (3).




- Angle the dashboard environment panel outwards so that it is possible to insert a couple of fingers between the centre console and the side of the dashboard environment panel
- Pull the dashboard environment panel downwards while maintaining the same angle. Remove the dashboard environment panel. Some force is required because the panel is tightly installed
- Disconnect the connectors on the reverse of the dashboard environment panel. Put the dashboard environment panel to one side.

Note! If any of the outer hooks break off, these must be repaired. The method for this can be found in the service information in the section covering the dashboard.




- Remove the screws (1) from the radio bracket
- Pull out the bracket with the radio (pull the lower corner while pressing downwards)
- Disconnect the radio connectors. Remove the bracket with the radio.





Remove:
- right side panel (1) by turning the screw clip at the rear edge of the panel half a turn. Pull the panel outwards and backwards
- the sill trim panel (2) at the right front door
- the covers (3) for the front seat mounting
- the two screws (4).




- Tip the seat back
- Fold the floor carpet forward to access the two air ducts (1).

Applies to S60 and S80




- Remove the seat cushion (1). First lift the front edge of the cushion and then pull forwards
- Fold the right rear backrest forward.

Applies to the V70

Illustration A




- Fold the right rear seat cushion forward.

Illustration B




- Fold the right rear backrest forward.

Illustration C




- Remove the right side cushion. First pull the upper edge of the cushion backwards. Then lift the cushion.




- Pull the door sill out of the right-hand rear door. Start at the rear edge
- Push the floor carpet and insulation panel to one side to access the connectors under the lower mountings.

Cargo compartment preparations (S60)




- Remove the cargo compartment carpet at the rear edge. First turn the two handles (1) 90°.




- Pull up the front of the cargo compartment carpet. Fold the front half back over the rear half of the cargo compartment carpet.




- Slide the entire cargo compartment carpet forward slightly. Twist slightly to remove the cargo compartment carpet through the tailgate opening.

Cargo compartment preparations (S60 and S80)

- Remove the cargo compartment carpet.




- Press the centres of the clips at the lower edge of the foldable side panel on the left-hand side until a click is heard.




- Turn the handle (1) on the right-hand side through 90°
- Fold the side panel inwards. Lift the panel out.





Remove:
- the clips (1) in the right front side panel in the cargo compartment
- the clips (2) at the top of the front edge on the side panel for the rear folding backrest
- the panel.

Cargo compartment preparations (V70)




- Remove the right-hand folding panel in the cargo compartment.




- Pull the rear edges of both floor hatches up. Pull the rear floor hatches backwards. Remove the rear floor hatches from the mountings.

Illustration B applies to the V70 with an auxiliary rear facing seat




- Remove the right side floor hatch by prising up one end. Use a weatherstrip tool.




- Remove the right-hand side panel. First remove the cover and the screw at the front edge
- Pull the top edge of the panel out until the clips release
- Fold the panel inwards. Lift the panel out.

Illustration B applies to cars with an auxiliary rear facing seat




- Remove the right-hand side panel. First remove the cover and the screw from the front edge
- Pull the top edge of the panel out until the clips release
- Pull the seat belt out of the holder (1)
- Remove the safety cover. First bend out the hooks on the underside. Pull the cover straight up
- Fold the panel inwards. Lift the panel out.

Connection and finishing work





Note! Check that the correct end of the antenna cable is routed to the radio tray.

- Route the antenna cable up between the front air duct (1) and the firewall stay (2)
- Route the cable through the radio compartment
- Secure the cable in the stay (3). Use a tie strap from the kit
- Route the cable above and along the front air duct to the seat mounting member (4)
- Clamp the wiring to the existing cable harness (5). Use a tie strap from the kit.




- Route the cable (1) under the carpet along the right side of the car to the rear door
- Install protective caps on the lugs (2) for the cable ducts
- Route the cable above and along the front cable duct (3). Continue along the left-hand side of the rear cable duct (4).

Illustration A applies to the S60 and the S80





Illustration B applies to the V70




- Route the cable (1) out through the hole in the bodywork at the wheel arch and along the right-hand side of the rear cable duct (2) to the right tail lamp.




- Connect the cable (2) for the antenna amplifier (1) to the connector (3) for the antenna in the bumper
- Position the antenna amplifier on the edge of the panel in front of the right tail lamp as illustrated
- Tighten the antenna amplifier to the edge of the panel
- Connect the routed cable to the socket (4) on the antenna amplifier.

- Clamp the cable along the cable duct in the cargo compartment. Use tie straps from the kit.
- Reinstall the panels in the cargo compartment
- Reinstall the sill trim panel in the right-hand rear door
- Fold the seat cushion back into place
- Fold the backrest back into place
- Fold the right front floor carpet back into place.

Reinstall:
- the sill trim panel in the right front door
- the seat. Tighten the seat using the two new screws from the kit. Tighten to 40 Nm (29.5 ft.lb)
- the two covers
- the right side panel for the centre console.





Note! If there are two black electrical cables in the connector, remove the right-hand (looking from the back of the connector) electrical cable. Secure the right-hand electrical cable. Install the new electrical cable.

- Connect the antenna cable to the two-pin connector (1), disconnected from the radio, to the spare terminal. Pry up the connector at the rear edge. Pull out the green plastic catch (2)
- Insert the cable in the free terminal (3). Lock the cable in place using the catch.

- Insert the radio in the radio tray. Connect the antenna cable and the connectors to the radio
- Reinstall the bracket with the radio.
- Connect the connectors to the dashboard environment panel. Reinstall the dashboard environment panel.
- Reinstall the panel in front of the gear selector lever.




- Turn the ignition key to position II
- Reconnect the battery negative lead
- Re-position the cargo compartment carpet
- Fold the rear floor hatch back into position.