Programming the Driver Information Module (DIM)
Programming the driver information module (DIM)
Programming the driver information module (DIM)
The following data can be programmed into the driver information module (DIM).
Programming:
- Conditions for the service reminder indicator (SRI) to light, mileage, time and engine hours
- If the instrument panel should display zeroes for the mileage
- Unit for temperature
- Unit in the trip computer (only applies to cars with trip computers)
- 12 or 24 hour clock display
- Activation and deactivation of the parking brake warning. Only applies to cars of structure week 200221 or later.
Continue - Selecting instrument type
-------------------------------------------------
Selecting instrument type
Select one of the following alternatives (for kilometers or miles). If the speedometer goes from 0-260 the combined instrument panel is intended for kilometers, if it goes from 0-160 it is intended for miles.
1. Km
2. Miles.
Select one of the above options.
1 - Checking the distance conditions for service
2 - Checking the distance conditions for service
-------------------------------------------------
Checking the distance conditions for service
Programming the distance covered for service
Programming the distance covered for service (km)
- Ignition on.
There are three service parameter units which can be programmed. Using this parameter, the number of km (miles) is set which the car must cover before the SRL lamp switches on. (Service reminder lamp)
Choices can be made between 5000, 7500, 10000, 15000 or 20000 km (miles).
Read the programmed data.
If the service parameter is to be changed, mark the desired value in the scrolling list and start the programming.
Continue - DONE
------------------------
DONE - Checking time conditions for service
-------------------------------------------------
Checking the distance conditions for service
Programming distance conditions for service
Programming distance conditions for service (miles)
- Ignition on.
There are three programmable service parameters. This parameter is used to set the number of miles a car can be driven before the Service Reminder Indicator (SRI) is lit. (Service reminder lamp)
2,500, 5,000, 6000, 7,500 10,000 or 12000 miles can be selected.
Read off the parameter that is programmed.
To change the service parameter, mark the desired value in the scrolling list and start programming.
Continue - DONE
------------------------
DONE - Checking time conditions for service
-------------------------------------------------
Checking time conditions for service
DONE - Checking engine time conditions for service
-------------------------------------------------
Checking engine time conditions for service
Programming the engine service time parameters
Programming the engine service time parameters
There are three service parameter units which can be programmed. Using these parameters, the number of hours is set which the engine may run before the SRL lamp switches on. (Service reminder lamp).
The permitted settings are 500, 750 or 1000 hours.
Read the input data.
If the service parameter is to be changed, key the necessary value into the scrolling list and start the programming.
Continue - DONE
------------------------
DONE - Checking customer setting zeroes
-------------------------------------------------
Checking customer setting zeroes
Programming of zeros (customer preference)
Programming of zeros (customer preference)
The zeros in the instrument can be set to be displayed or hidden. If the zeros are displayed, all the positions before the number of kilometres covered are filled with zeros, and if the zeros are hidden these positions remain blank.
Read the input data.
If the value is to be changed, enter the necessary value into the scrolling list and start the programming.
Continue - DONE
------------------------
DONE - Checking the units of measurement for temperature (customer setting)
-------------------------------------------------
Checking the units of measurement for temperature (customer setting)
Programming units of measurement for temperature (customer programmable)
Programming units of measurement for temperature (customer programmable)
The units of measurement for the temperature can be set.
Options are: Celsius or Fahrenheit.
Read off the parameter that is programmed.
To change the value, mark the desired value in the scrolling list and start programming.
Continue - DONE
------------------------
DONE - Checking the units of measurement for the trip computer (customer setting)
-------------------------------------------------
Checking the units of measurement for the trip computer (customer setting)
Programming of trip computer unit (customer preference)
Programming of trip computer unit (customer preference)
A desired unit may be set for the trip computer if you have purchased this function. The permitted choices are litres, GB gallons or US gallons.
Read the input data.
If the value is to be changed, enter the necessary value into the scrolling list and start the programming.
Continue - DONE
------------------------
DONE - Checking the units of measurement for the trip computer (customer setting)
-------------------------------------------------
Checking the units of measurement for the trip computer (customer setting)
Programming of clock by customer
Programming of clock by customer
The clock may be displayed.
This may be either a 12 hour display or 24 hour display.
Read the input data.
If the value is to be changed, key the necessary value into the scrolling list and start the programming.
Continue - DONE
------------------------
DONE - Programming parking brake warning
-------------------------------------------------
Programming parking brake warning
- Ignition on.
To be able to activate and deactivate the parking brake warning, the car must be built in structure week 200221 or later, week 21 in 2002.
Read off the car structure week by clicking on the VCT2000 symbol.
Does the vehicle have the above structure week or later?
Yes - Programming parking brake warning
No - DONE
-------------------------------------------------
Programming parking brake warning
- Ignition on.
It is possible to activate or deactivate the parking brake warning.
Read off the programming by clicking on the VCT2000 symbol.
To alter the parameter, mark the desired value and start programming.
Continue - DONE
-------------------------------------------------