Signal Too Low or Signal Missing
Signal too low or signal missing
Checking for permanent or intermittent faults
- Ignition on.
Press the switch for the power window to check the function of the power window mechanism.
Is the power window control operating correctly?
Yes - Intermittent fault
No - Checking the connectors
-------------------------------------------------
Checking the connectors
- Ignition off.
Check that the fuses are intact.
Check the control module and power window lift motor connectors. Check for contact resistance and oxidation.
Other information:
- For further information about the fuses and relays, see the Wiring Diagram
- To access the driver/passenger door module (DDM/PDM), see Driver's door module / passenger door module (DDM/PDM), replacing Driver's Door Module/Passenger Door Module (DDM/PDM), Replacing
- To access and replace the power window mechanism, see Window lift mechanism front side door, replacing Window Lift Mechanism Front Side Door, Replacing
- Checking the power supply and ground terminals Checking the Voltage/Ground Terminal, Driver Door Module (DDM)/ Passenger Door Module (PDM)
- Checking wiring and terminals Checking Wiring And Terminals.
Continue - Checking the cable
-------------------------------------------------
Checking the cable
Check the cable between door control module connector terminal #B4 and power window lift motor connector terminal #3. Check for an open-circuit. Check for a short-circuit to ground.
Check the cable between door control module connector terminal #B3 and power window lift motor connector terminal #6. Check for an open-circuit. Check for a short-circuit to ground.
Remedy as necessary.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box
- For further information about signals and other values, see Signal specification Pinout Values and Diagnostic Parameters
- To access the control module, see Driver's door module / passenger door module (DDM/PDM), replacing Driver's Door Module/Passenger Door Module (DDM/PDM), Replacing
- Checking the power supply and ground terminals Checking the Voltage/Ground Terminal, Driver Door Module (DDM)/ Passenger Door Module (PDM)
- Checking wiring and terminals Checking Wiring And Terminals.
Was the cable OK?
Yes - Replacing the component
No - Verification
-------------------------------------------------
Replacing the component
Replace the window lift mechanism. See Window lift mechanism front side door, replacing Window Lift Mechanism Front Side Door, Replacing.
Ignition on.
Move the window to its upper limit position using manual control.
Initialize the window.
From model year 2003 inclusive, the window will lower approximately 10 centimeters and then close again during initialization.
Continue - Verification
-------------------------------------------------
Verification
Verification
Verification
Hint: After the repair it is necessary to check that the fault has been rectified.
- Ignition off.
- Connect the connectors, install the components, etc.
- Ignition on.
Check that window operates by raising/lowering window to its end stops.
Does window operate?
Yes - VERIFIED
No - VERIFICATION FAILED
------------------------
VERIFIED - Fault Found
VERIFICATION FAILED - Fault-tracing information
-------------------------------------------------
Intermittent fault
Check the connectors for the control module and power window lift motor. Check for contact resistance and oxidation. Check for loose connections.
Check the cable between control module connector terminal #B4 and power window lift motor connector terminal #3. Check for an intermittent open-circuit.
Check the cable between the control module connector terminal #3B and the power window lift motor connector terminal #6. Check for an intermittent open-circuit.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box
- For further information about signals and other values, see Signal specification Pinout Values and Diagnostic Parameters
- To access the control module, see Driver's door module / passenger door module (DDM/PDM), replacing Driver's Door Module/Passenger Door Module (DDM/PDM), Replacing
- To access and replace the power window mechanism, see Window lift mechanism front side door, replacing Window Lift Mechanism Front Side Door, Replacing
- Checking the power supply and ground terminals Checking the Voltage/Ground Terminal, Driver Door Module (DDM)/ Passenger Door Module (PDM)
- Checking wiring and terminals Checking Wiring And Terminals.
Continue - Fault-tracing information
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
Do you want to exit fault-tracing?
Yes - FAULT-TRACING FAILED
No - Attempt New Test
------------------------
FAULT-TRACING FAILED - No Fault Found
Attempt New Test - Checking for permanent or intermittent faults
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Do you want to view the information again?
Yes - Attempt New Test
No - Fault Found
------------------------
FAULT FOUND - Fault Found
Attempt New Test - Checking for permanent or intermittent faults
-------------------------------------------------