Chassis Number 26213 - 999999
Signal too low
Checking the P-shift lock solenoid
- Ignition on
- Gear selector in position P
- Try moving the gear selector to another position without depressing the brake pedal. It should not be possible to move the gear selector
- Depress the brake pedal and try moving the gear selector to another position. It should now be possible to move the gear selector to another position.
Was the function OK?
Yes - Intermittent fault
No - Checking the wiring and component
-------------------------------------------------
Checking the wiring and component
Check the cable between the gear selector module (GSM) and the shift lock solenoid. Check for a short-circuit to ground.
If no fault is found in the wiring, connect an ohmmeter to solenoid connector terminals #1 and #2 (solenoid side). The resistance must be 15-25 ohms.
Replace the solenoid if the resistance is incorrect. Replace the printed circuit board in the top panel if the resistance is OK.
Other information - V70 and V70 XC
- To replace the shift lock solenoid, see Solenoid back-up (reverse) inhibitor, replacing Solenoid Back-Up (Reverse) Inhibitor, Replacing
- To replace the circuit board in the top panel (standard), see Printed circuit board gear selector assembly/top panel, replacing Printed Circuit Board Gear Selector Assembly/Top Panel, Replacing
- To replace the circuit board in the top panel (Geartronic), see Printed circuit board gear selector assembly/top panel Geartronic, replacing Printed Circuit Board Gear Selector Assembly/Top Panel Geartronic, Replacing
- Checking wiring and terminals Checking Wiring And Terminals
Other information - S60
- To replace the shift lock solenoid, see Solenoid back-up (reverse) inhibitor, replacing, B5254T2, AW55-50/51SN Solenoid Back-Up (Reverse) Inhibitor, Replacing
- To replace the circuit board in the top panel (standard), see Printed circuit board gear selector assembly/top panel, replacing, B5254T2, AW55-50/51SN Printed Circuit Board Gear Selector Assembly/Top Panel, Replacing
- To replace the circuit board in the top panel (Geartronic), see Boot, gear selector, replacing, B5254T2, AW55-50/51SN Boot, Gear Selector, Replacing
- Checking wiring and terminals Checking Wiring And Terminals
Continue - Verification
-------------------------------------------------
Verification
Verification
Hint: After carrying out the repair, check that the fault has been remedied.
- Ignition on.
- Gear selector in position P.
Try moving the gear selector to another position without depressing the brake pedal. It should not be possible to move the gear selector.
Depress the brake pedal and try moving the gear selector to another position. It should now be possible to move the gear selector.
Was the function OK?
Yes - VERIFIED
No - VERIFICATION FAILED
------------------------
VERIFICATION FAILED - Fault-tracing information
PAPER - No Fault Found
VERIFIED - Fault Found
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
Do you want to exit fault-tracing?
Yes - FAULT-TRACING FAILED
No - Attempt New Test
------------------------
FAULT-TRACING FAILED - FAULT-TRACING FAILED
Attempt New Test - Checking the P-shift lock solenoid
-------------------------------------------------
Intermittent fault
Check the gear selector module (GSM) and solenoid connectors. Check for intermittent contact resistance.
Check the cable between the gear selector module (GSM) and the shift lock solenoid. Check for an intermittent short-circuit to ground.
Remedy as necessary.
Other information:
- To replace the shift lock solenoid (V70), see Solenoid back-up (reverse) inhibitor, replacing Solenoid Back-Up (Reverse) Inhibitor, Replacing
- To replace the shift lock solenoid (S60), see Solenoid back-up (reverse) inhibitor, replacing, B5254T2, AW55-50/51SN Solenoid Back-Up (Reverse) Inhibitor, Replacing
- Checking wiring and terminals Checking Wiring And Terminals
Continue - Fault-tracing information
DONE
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Do you want to view the information again?
Yes - Attempt New Test
No - Fault Found
------------------------
Attempt New Test - Checking the P-shift lock solenoid
FAULT FOUND - DONE
-------------------------------------------------