Chassis Number 26213 - 999999

Faulty signal. Permanent fault

Checking the transmission input speed sensor signal








- Ignition off
- Check the transmission control module (TCM) and transmission connectors. Check for contact resistance and oxidation according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault. Remedy if necessary
- Reinstall the components, reconnect the connectors etc.
- Gear selector in position P
- Start the engine and let it run at idle speed
- Read off the transmission input speed.
Check that the transmission input speed is updated.
Compare with the engine speed (RPM).
If the transmission speed increases, the cause of the fault was loose connections in the control module or transmission speed sensor connectors.

Other information:
- To disconnect the transmission control module (TCM), see Transmission control module (TCM), replacing, B5244T5, AW55-50/51SN, B5254T2, AW55-50/51SN, B5254T2, AW50/51 AWD Service and Repair
- To disconnect the automatic transmission connector, see Connectors, transmission, disconnecting / connecting, B5244T5, AW55-50/51SN, B5254T2, AW55-50/51SN, B5254T2, AW50/51 AWD Procedures
- For information about signals, see Signal description. Transmission control module (TCM), AW50/51 AWD, AW55-50/51SN Signal Description. Transmission Control Module (TCM).





Does the transmission input speed increase with engine speed (RPM)?

Yes - Fault Found

No - Checking wiring and sensors

-------------------------------------------------

Checking wiring and sensors




- Ignition off
- Connect the breakout box.
Check the power supply cable for the transmission input speed sensor between control module terminal #A59 (#A59) and transmission connector terminal #A2. Check for an open-circuit according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault. Check for a short-circuit to ground according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault. Check for a short-circuit to supply voltage according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault.
Check the signal cable between control module terminal #A41 (#A41) and transmission connector terminal #A1. Check for an open-circuit according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault. Check for a short-circuit to ground according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault. Check for a short-circuit to supply voltage according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault.

Hint: With the control module connected and the ignition on, the voltage between transmission output speed sensor connector terminals #1 and #2 must be approximately 1-3 V below Ubat.

Remedy as necessary.

Other information:
- To connect the breakout box, see Connecting the breakout box, B5244T5, B5254T2 Connecting the Breakout Box
- To disconnect the automatic transmission connector, see Connectors, transmission, disconnecting / connecting, B5244T5, AW55-50/51SN, B5254T2, AW55-50/51SN, B5254T2, AW50/51 AWD Procedures
- To replace the transmission input speed sensor, see Replacing the transmission input speed sensor and the transmission output speed sensor Input Speed Sensor/Output Speed Sensor, Replacing
- For information about signals, see Signal description. Transmission control module (TCM), AW50/51 AWD, AW55-50/51SN Signal Description. Transmission Control Module (TCM).









Was a fault detected?

Yes - Verification

No - No Fault Found

-------------------------------------------------

Verification




Verification

Hint: After carrying out the repair, check that the fault has been remedied.








- Ignition off.
- Reinstall the connectors, components etc.
- Start the engine and let it idle.
- Gear selector in position P.
- Read off the transmission speed.
Depress the accelerator pedal (AP) and check that engine speed (RPM) is updated.
Compare with the engine speed (RPM).





Is the speed updated?

Yes - VERIFIED

No - VERIFICATION FAILEDPAPER

------------------------

VERIFIED - Fault Found

VERIFICATION FAILED - Fault-tracing information

PAPER - No Fault Found

-------------------------------------------------

Fault-tracing information




Information

Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.

Do you want to exit fault-tracing?

Yes - FAULT-TRACING FAILED

No - Attempt New Test

------------------------

FAULT-TRACING FAILED - FAULT-TRACING FAILED

Attempt New Test - Checking the transmission input speed sensor signal

-------------------------------------------------