No Signal. Intermittent Fault

No signal. Intermittent fault

STC or DSTC




Question

Question

Does the car have a DSTC system?

Yes - DSTC

No - STC

------------------------

STC - Checking the wiring and connections

DSTC - DSTC

-------------------------------------------------

Checking the wiring and connections
Check the connectors of the control unit and the relevant wheel sensor for intermittent contact resistance and oxidation, as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults.
Check the wires between relevant wheel sensor connector:

Diagnostic trouble code ABS-0030 Rear LH wheel sensor
#1 and control unit #6

Diagnostic trouble code ABS-0040 Rear RH wheel sensor
#1 and control unit #22
for an intermittent open circuit as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults , for an intermittent short circuit to ground as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults , and for an intermittent short circuit to voltage supply as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults.
Check the wires between relevant wheel sensor connector:

Diagnostic trouble code ABS-0030 Rear LH wheel sensor
#2 and control unit #5

Diagnostic trouble code ABS-0040 Rear RH wheel sensor
#2 and control unit #23
for an intermittent open circuit as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults , for an intermittent short circuit to ground as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults , and for an intermittent short circuit to voltage supply as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults.
Do the necessary corrective action.

Additional information:
- To connect the test box, see Connecting the ABS breakout box Pinout Values and Diagnostic Parameters.
- For additional values, see Signal specification, ABS control module Signal Specification.









Select Continue when the fault has been rectified.

Continue - Trouble-shooting information
DONE

-------------------------------------------------

Trouble-shooting information




Information

Fault-tracing information
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).

Do you want to view the information again?

Yes - Attempt New Test

No - Fault Found

------------------------

Attempt New Test - Checking the wiring and connections

DONE - DONE

FAULT FOUND - Fault Found

-------------------------------------------------

DSTC





No signal. Intermittent fault

Checking the wiring and connections
Check the connectors of the control unit and the relevant wheel sensor for intermittent contact resistance and oxidation, as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults.
Check the wires between relevant wheel sensor connector:

Diagnostic trouble code ABS-0030 Rear LH wheel sensor
#1 and control unit #36

Diagnostic trouble code ABS-0040 Rear RH wheel sensor
#1 and control unit #6
for an intermittent open circuit as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults , for an intermittent short circuit to ground as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults , and for an intermittent short circuit to voltage supply as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults.
Check the wires between relevant wheel sensor connector:

Diagnostic trouble code ABS-0030 Rear LH wheel sensor
#2 and control unit #37

Diagnostic trouble code ABS-0040 Rear RH wheel sensor
#2 and control unit #7
for an intermittent open circuit as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults , for an intermittent short circuit to ground as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults , and for an intermittent short circuit to voltage supply as described in Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults.
Do the necessary corrective action.

Additional information:
- To connect the test box, see Connecting the ABS/DSTC breakout box Pinout Values and Diagnostic Parameters.
- For additional values, see Signal specification, ABS / DSTC (dynamic stability and traction control) control module Signal Specification.









Select Continue when the fault has been rectified.

Continue - Trouble-shooting information
DONE

------------------------

Trouble-shooting information
Information
Attempt New Test - Checking the wiring and connections

DONE - DONE

FAULT FOUND - Fault Found

------------------------

DONE - DONE

FAULT FOUND - Fault Found

-------------------------------------------------