Internal Battery Fault
Internal battery fault
Erasing diagnostic trouble codes (DTCs)
- Ignition for 30 seconds.
Erase diagnostic trouble codes (DTCs).
Select "Continue" when the diagnostic trouble codes (DTCs) have been erased.
Continue - Reading off diagnostic trouble codes (DTCs)
-------------------------------------------------
Reading off diagnostic trouble codes (DTCs)
- Ignition on.
- Wait for 30 seconds.
- Ignition off. Remove the key from the ignition switch. Close all the doors and the hood.
- Lock the car with the remote control.
- Wait for approximately 30 seconds.
- Unlock the car with the remote control.
- Ignition on.
Read off diagnostic trouble codes (DTCs).
Did diagnostic trouble code (DTC) GLA-312 recur?
Yes - Checking the wiring
No - Intermittent fault
-------------------------------------------------
Checking the wiring
- Expose the VGLA control module according to Replacing the control module Replacing the Control Module.
- Remove the siren according to Replacing the siren Replacing the Siren.
- Disconnect the siren connector.
- Ignition on.
Check fuse 29.
Check the cable between terminal #4 on the 15-I rail in the relay box and the siren connector terminal #1 for an open-circuit according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault and for an short-circuit to ground according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault. Check the siren and control module connectors for contact resistance and oxidation according to Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault.
Other information:
- The voltage between siren connector terminal #1 and ground should be battery voltage when the ignition is on.
Remedy as necessary.
Was a fault detected?
Yes - Erasing diagnostic trouble codes (DTCs)
No - Replacing the component
-------------------------------------------------
Replacing the component
- Ignition off.
- Siren removed.
- Try a new battery.
- Ignition on.
Erase diagnostic trouble codes (DTCs).
Select "Continue" when the diagnostic trouble codes (DTCs) have been erased.
Continue - Reading off diagnostic trouble codes (DTCs)
-------------------------------------------------
Reading off diagnostic trouble codes (DTCs)
- Ignition on.
- Wait at least 1 minute.
- Ignition off. Remove the key from the ignition switch and close all doors, the hood, trunk lid or tailgate.
- Lock the car with the remote control.
- Wait for approximately 10 seconds.
- Unlock the car with the remote control.
- Ignition on.
Read off diagnostic trouble codes (DTCs).
Did diagnostic trouble code (DTC) GLA-312 recur?
Yes - Replacing the component
No - FAULT FOUND
-------------------------------------------------
Replacing the component
Try a new siren according to Replacing the siren Replacing the Siren.
Continue - Erasing diagnostic trouble codes (DTCs)
-------------------------------------------------
Erasing diagnostic trouble codes (DTCs)
- Ignition on.
Erase diagnostic trouble codes (DTCs).
Select "Continue" when the diagnostic trouble codes (DTCs) have been erased.
Continue - Verification
-------------------------------------------------
Verification
Hint: After carrying out the repair it is important to check
that the fault has been corrected as follows:
- Ignition on.
- Wait for approximately 1 minute.
- Ignition off.
- Remove the key from the ignition switch. Close all doors and the hood.
- Lock the car with the remote control.
- Wait approximately 10 seconds.
- Unlock the car with the remote control.
- Ignition on.
Read off diagnostic trouble codes (DTCs).
Does diagnostic trouble code (DTC) GLA-312 recur?
Yes - Fault-tracing information
No Fault Found
No - FAULT FOUND
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
Do you want to exit fault-tracing?
Yes - Exit fault-tracing
No - Attempt New Test
------------------------
FAULT-TRACING FAILED - No Fault Found
Attempt New Test - Erasing diagnostic trouble codes (DTCs)
-------------------------------------------------
Intermittent fault
- Check the siren and the VGLA control module connectors for loose connections according to Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults and for contact resistance and oxidation according to Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults.
Continue - Fault-tracing information
No Fault Found
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Do you want to view the information again?
Yes - Attempt New Test
No - FAULT FOUND
------------------------
Attempt New Test - Erasing diagnostic trouble codes (DTCs)
-------------------------------------------------