ABS Control Module and ABS Hydraulic Unit Overview
ABS Control Module and ABS Hydraulic Unit Overview
1 ABS Hydraulic Unit (N55)
• Removing and installing, with 5-cylinder gasoline engine, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit.
• Removing and installing, with 6-cylinder gasoline engine, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit.
• Removing and installing, with 4-cylinder diesel engine, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit.
2 ABS Control Module (w/EDL) (J104)
• Removing and installing, with 5-cylinder gasoline engine, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit.
• Removing and installing, with 6-cylinder gasoline engine, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit.
• Removing and installing, with 4-cylinder diesel engine, refer to => [ ABS Control Module and ABS Hydraulic Unit ] ABS Control Module and ABS Hydraulic Unit.
• Disconnecting the ABS control module (J104) from the ABS hydraulic unit (N55) => [ ABS Control Module, Separating from ABS Hydraulic Unit ] ABS Control Module, Separating from ABS Hydraulic Unit.
3 Bolt
• 2 Nm +/- 0.8 Nm
• Quantity: 4
• Always replace if removed.
4 Brake Line
• 14 Nm
• To left front brake caliper.
• Identification: Diameter 5.25 mm and tube fitting with M10 x 1 thread.
5 Brake Line
• 14 Nm
• ABS hydraulic unit (N55) for the master brake cylinder/primary piston circuit.
• Identification: 6.5 mm and tube fitting with M12 x 1 thread.
6 Brake Line
• 14 Nm
• To right front brake caliper.
• Identification: 5.25 mm and tube fitting with M12 x 1 thread.
7 Brake Line
• 14 Nm
• ABS hydraulic unit (N55) for the master brake cylinder/secondary piston circuit.
• Identification: 6.5 mm and tube fitting with M12 x 1 thread.
8 Brake Line
• 14 Nm
• Master brake cylinder/primary piston circuit for the ABS hydraulic unit (N55).
• Identification: 6.5 mm and tube fitting with M12 x 1 thread
9 Brake Line
• 14 Nm
• Master brake cylinder/secondary piston circuit for the ABS hydraulic unit (N55).
• Identification: 6.5 mm and tube fitting with M12 x 1 thread
10 Brake Booster
• Overview, refer to => [ Brake Booster and Master Brake Cylinder Overview ] Brake Booster and Master Brake Cylinder Overview.
• Removing and installing, with 5-cylinder gasoline engine, refer to => [ Brake Booster ] Brake Booster.
• Removing and installing, with 6-cylinder gasoline engine, refer to => [ Brake Booster ] Brake Booster.
• Removing and installing, with a 4-cylinder diesel engine, refer to => [ Brake Booster ] Brake Booster.
11 Brake Line
• 14 Nm
• To left rear brake caliper/brake cylinder.
• Identification: Diameter 5.25 mm and tube fitting with M12 x 1 thread.
12 Brake Line
• 14 Nm
• To the right rear brake caliper/brake cylinder.
• Identification: Diameter 5.25 mm and tube fitting with M10 x 1 thread.
13 Hex Bolt
• 8 Nm
14 Rubber Insulation
15 Bracket
• After installing, make sure it fits properly.
16 Bolt
• 8 Nm
• Quantity: 3
17 Nut
• 8 Nm
• Quantity: 2
18 Bracket
19 Rubber Insulation
• Do not press the rubber bushings out of the bracket when installing the mount.