Subframe, Transverse Link and Tie Rods Assembly Overview, from MY 2011
Subframe, Transverse Link and Tie Rods Assembly Overview, from MY 2011
1 Eccentric Bolt
• For camber setting.
• After loosening, perform vehicle alignment. Refer to => [ Wheel Alignment ] Wheel Alignment.
2 Eccentric Bolt
• For toe setting.
• After loosening, perform vehicle alignment. Refer to => [ Wheel Alignment ] Wheel Alignment.
3 Eccentric Washer
• Inner bore with tab.
4 Nut
• M12 x 1.5
• 95 Nm
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Suspension, Lifting to Curb Weight Position ] Rear Suspension, Lifting to Curb Weight Position.
5 Eccentric Washer
• Inner bore with tab.
6 Nut
• M12 x 1.5
• 95 Nm
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Suspension, Lifting to Curb Weight Position ] Rear Suspension, Lifting to Curb Weight Position.
7 Subframe
8 Bolt
• M12 x 1.5 x 95
• 90 Nm + 90° turn
• Always replace if removed.
9 Lower Transverse Link
• Removing and installing, refer to => [ Lower Transverse Link, from MY 2011 ] Lower Transverse Link, from MY 2011.
10 Nut
• M12 x 1.5
• 90 Nm + 90° turn
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Suspension, Lifting to Curb Weight Position ] Rear Suspension, Lifting to Curb Weight Position.
11 Bolt
• Always replace if removed.
12 Threaded Rivet
• M6
13 Expanding Rivet
14 Stone Protection Plate
15 Bolt
• 8 Nm
16 Nut
• M14 x 1.5
• 130 Nm + 90° turn
• Self-locking
• Always replace if removed.
17 Washer
18 Bolt
• 130 Nm + 90° turn
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Suspension, Lifting to Curb Weight Position ] Rear Suspension, Lifting to Curb Weight Position
19 Washer
20 Upper Transverse Link
• Removing and installing, refer to => [ Upper Transverse Link, from MY 2011 ] Upper Transverse Link, from MY 2011.
21 Washer
22 Nut
• M14 x 1.5
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Suspension, Lifting to Curb Weight Position ] Rear Suspension, Lifting to Curb Weight Position.
23 Wheel Bearing Housing
• Removing and installing, refer to => [ Wheel Bearing Housing ] Wheel Bearing Housing.
24 Washer
25 Bolt
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Suspension, Lifting to Curb Weight Position ] Rear Suspension, Lifting to Curb Weight Position.
26 Tie Rod
• Closed in direction of travel (the right and left tie rods are different).
• Removing and installing, refer to => [ Tie Rod, from MY 2011 ] Tie Rod, from MY 2011.
27 Bolt
• Always replace if removed.
28 Nut
• M12 x 1.5
• 90 Nm + 90° turn
• Self-locking
• Always replace if removed.
• Always tighten threaded connections in curb weight position. Refer to => [ Rear Suspension, Lifting to Curb Weight Position ] Rear Suspension, Lifting to Curb Weight Position.