Seat Belts, Inspecting
Seat Belts, Inspecting
After every accident the seat belt system must be inspected systematically! If damage is determined when inspecting the check points, customer must be informed regarding necessity of changing belts.
=> [ Belt Webbing, Checking ]
=> [ Retractor Locking Function, Checking ]
=> [ Belt Latch, Inspecting ]
=> [ Belt Latch Function, Testing ]
=> [ Belt Guide Rings and Locking Tongue, Checking ]
=> [ Mounting Components and Mounting Points, Checking ]
Belt Webbing, Checking
- Pull belt completely out of retractor or lap belt adjustment tongue.
- Make sure the seat belt is not dirty. If necessary, wash with a mild soap solution. Refer to Owner's Manual.
• If one of the types of damage (1 or 2) shown in the following is detected on a vehicle which has been in an accident - seat belt must be replaced completely with seat belt latch and seat belt height adjuster.
• If one kind of damage under points 1, 2, 3 and 4 is detected on a vehicle which has not been in an accident, only the damaged seat belt needs to be replaced.
• Belt webbing cut, torn or chafed.
• Webbing loops on belt edge torn.
• Burn marks from cigarettes or similar.
• One side of belt edge deformed or area of belt edge is wavy.
Retractor Locking Function, Checking
The belt retractor has two locking functions.
• The first locking function is initiated by belt being jerked out of the retractor (belt extraction acceleration).
Checking
- Pull belt webbing out of retractor with a firm jerk.
• No locking function - replace compete seat belt with belt latch.
• If difficulties are experienced when pulling out or retracting belt, first check whether position of retractor has been altered.
• The second locking function is initiated by change in vehicle velocity (vehicle-dependent locking function). For this, the vehicle must be moved on a level surface.
Checking
- Fasten seat belt.
- Accelerate vehicle to 12 mph (20 km/h) and then perform a full braking maneuver with foot brake.
• If the locking mechanism does not lock the seat belt during the braking maneuver, the complete seat belt with seat belt latch must be replaced.
For safety reasons, road test should be carried out on traffic-free stretch to ensure that other motorists/pedestrians etc. are not endangered.
Belt Latch, Inspecting
- Inspect the seat belt latch for cracks and chipping.
• If damaged, replace the complete seat belt and the seat belt latch.
Belt Latch Function, Testing
Check the seat belt latch:
- Insert locking tongue into the seat belt latch until it audibly engages. Check whether locking mechanism is properly engaged by giving belt webbing a firm jerk.
• If locking tongue fails to engage properly into the seat belt latch even once during at least 5 tests, replace complete seat belt with seat belt latch.
Check release mechanism:
- Press the seat belt latch to release the seat belt.
- When belt is slack, locking tongue must spring out of seat belt latch on its own.
• Perform test at least 5 times. If locking tongue fails even once to spring out, replace complete seat belt with seat belt latch.
Under no circumstances may grease be used to eliminate noise or stiffness at belt buckle buttons.
Belt Guide Rings and Locking Tongue, Checking
Plastic-coated fittings face the load (seat belt on during accident) of the belt system parallel to the small grooves (wear created by significant usage, in contrast, is recognizable on the basis of the smooth, stripe-free abrasion).
- Inspect for deformation, chipping and cracks in plastic.
• If scoring and/or damage is discovered, replace complete seat belt with seat belt latch.
Mounting Components and Mounting Points, Checking
• Latch bracket deformed (stretched)
• Height adjuster not functional
• Mounting points (seat, pillar, vehicle floor) distorted or thread damaged
• If damage is discovered on these components, replace complete seat belt with seat belt latch.
• Replace anchorage points.
• In damage is discovered that is not accident-related, for example, wear, replace the particular part which is damaged.