Transmission and Valve Body Component Overview
Transmission and Valve Body Component Overview
1 Transmission Fluid Inspection Plug
• Fluid level, checking and filling. Refer to => [ Transmission Fluid Level, Checking and Adding ] Transmission Fluid Level, Checking and Adding.
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
2 Seal
• Always replace.
3 Overflow Tube
• Remove in order to drain the transmission fluid.
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
4 Transmission Fluid Pan
• Removing and installing, refer to => [ Transmission Fluid Pan ] Service and Repair.
5 Bolt
• Tighten the bolts diagonally and in several steps.
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
6 Gasket
• With spacers (quantity: 8).
• Check before installing.
• Replace if brittle, cracked or deformed.
7 Magnet
• Quantity: 2, in the depressions in the transmission fluid pan.
• Clean before installing the pan.
8 Bolt
• Always replace.
• For attaching the valve body to the transmission.
• Quantity 12, with different lengths, refer to => [ Bolt lengths and locations on the valve body: ] Service and Repair.
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
9 Bolt
• Quantity: 3
• For attaching the transmission fluid filter to the valve body.
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
10 Transmission Fluid Filter
• Removing and installing, refer to => [ Transmission Fluid Filter ] Service and Repair.
11 Valve Body
• Removing and installing, refer to => [ Valve Body ] Service and Repair.
• Allocation, refer to the Parts Catalog.
12 Bolt
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
13 Bolt
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
14 Transmission Input Speed Sensor (G182)
• Removing and installing, refer to => [ Transmission Input Speed Sensor G182 ] Transmission Input Speed Sensor G182.
15 Bolt
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
16 Transmission Output Speed Sensor (G195)
• Removing and Installing, refer to => [ Transmission Output Speed Sensor G195 ] Transmission Output Speed Sensor G195.
17 Transmission Housing
• Illustrated here without the a transmission fluid cooler.
18 Vent Cap
19 Multifunction Transmission Range Switch (F125)
• Removing and installing, refer to => [ Multifunction Transmission Range Switch F125 ] Service and Repair.
• Adjusting, refer to => [ Multifunction Transmission Range Switch, Adjusting ] Adjustments.
20 Transmission Fluid Temperature Sensor (G93)
• Integrated into the wiring harness.
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
• Removing and installing, refer to => [ Solenoid Valve and Sensor Wiring Harness ] Service and Repair.
• Wire routing, refer to => [ Wire Routing, Connectors and Bracket on Valve Body ] Wire Routing, Connectors and Bracket on Valve Body.
21 Bolt
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
22 Bolt
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
23 Sensor Wiring Harness
• With the transmission fluid temperature sensor.
• For the transmission input and output speed sensors.
• Always replace the seal on the connector housing.
• Removing and installing, refer to => [ Solenoid Valve and Sensor Wiring Harness ] Service and Repair.
• Wire routing, refer to => [ Wire Routing, Connectors and Bracket on Valve Body ] Wire Routing, Connectors and Bracket on Valve Body.
• Allocation, refer to the Parts Catalog.
24 Seal
• Always replace.
25 Transmission Fluid Drain Plug
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
26 Selector Shaft Lever
• For the selector shaft.
• Removing and installing, refer to => [ Remove the selector lever from the selector shaft. ] Service and Repair.
27 Washer
28 Nut
• Installed position: The centering collar faces the washer - item 27 -.
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.
29 Spring
• Allocation, refer to the Parts Catalog.
30 Piston
31 Solenoid Valve Wiring Harness
• Always replace the seal on the connector housing.
• Removing and installing, refer to => [ Solenoid Valve and Sensor Wiring Harness ] Service and Repair.
• Wire routing, refer to => [ Wire Routing, Connectors and Bracket on Valve Body ] Wire Routing, Connectors and Bracket on Valve Body.
32 Bolt
• Tightening specification, refer to => [ Fastener Tightening Specifications ] Specifications.