Removal (from 07/2011)
INTERIOR PANELS / TRIM: ROOF HEADLINING (for Hatchback 3 Door): REMOVAL
1. REMOVE DECK BOARD ASSEMBLY Removal (from 07/2011)
2. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
Removal (from 07/2011)
3. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
Removal (from 07/2011)
4. REMOVE REAR SEATBACK ASSEMBLY (for Fold Down Seat Type)
Removal (from 07/2011)
5. REMOVE FRONT DOOR SCUFF PLATE RH
(a) Disengage the 8 claws and remove the front door scuff plate.
6. REMOVE FRONT DOOR SCUFF PLATE LH
HINT
Use the same procedure as for the RH side.
7. REMOVE COWL SIDE TRIM BOARD RH Removal (from 07/2011)
8. REMOVE COWL SIDE TRIM BOARD LH
HINT
Use the same procedure as for the RH side.
9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
(a) Remove the front door opening trim weatherstrip.
10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT
Use the same procedure as for the RH side.
11. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH
(a) Disengage the 2 claws and remove the anchor cover.
(b) Remove the bolt and separate the front seat outer belt.
12. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH
HINT
Use the same procedure as for the RH side.
13. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH
(a) Disengage the 8 clips and 10 claws.
(b) Disengage the 3 guides and remove the quarter trim panel.
14. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH
HINT
Use the same procedure as for the RH side.
15. REMOVE CENTER PILLAR UPPER GARNISH RH
(a) Remove the 2 screws and disengage the clip.
(b) Pass the front seat outer belt through the slit in the center pillar upper garnish and remove the center pillar upper garnish.
16. REMOVE CENTER PILLAR UPPER GARNISH LH
HINT
Use the same procedure as for the RH side.
17. REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag) Removal (from 07/2011)
18. REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)
HINT
Use the same procedure as for the RH side.
19. REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag) Removal (from 07/2011)
20. REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)
HINT
Use the same procedure as for the RH side.
21. REMOVE NO. 2 ROOM LIGHT ASSEMBLY Removal (from 07/2011)
22. REMOVE JACK HANDLE
23. REMOVE REAR FLOOR FINISH PLATE Removal (from 07/2011)
24. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
(a) Remove the bolt.
(b) Disengage the 2 claws and separate the rear seat 3 point type outer belt.
25. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
HINT
Use the same procedure as for the RH side.
26. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
(a) Remove the 3 screws.
(b) Disengage the 3 clips and the 3 claws and remove the deck trim side panel.
27. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
HINT
Use the same procedure as for the RH side.
28. REMOVE ROOF SIDE INNER GARNISH RH
(a) Disengage the 5 clips.
(b) Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
29. REMOVE ROOF SIDE INNER GARNISH LH
HINT
Use the same procedure as for the RH side.
30. REMOVE REAR ROOF SIDE RAIL GARNISH RH
(a) Disengage the 4 clips and remove the roof side rail garnish.
31. REMOVE REAR ROOF SIDE RAIL GARNISH LH
HINT
Use the same procedure as for the RH side.
32. REMOVE VISOR ASSEMBLY RH Removal (from 07/2011)
33. REMOVE VISOR ASSEMBLY LH
HINT
Use the same procedure as for the RH side.
34. REMOVE VISOR HOLDER Removal (from 07/2011)
35. REMOVE ASSIST GRIP ASSEMBLY Removal (from 07/2011)
36. REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/ Cover) Removal (from 07/2011)
37. REMOVE MAP LIGHT ASSEMBLY Removal (from 07/2011)
38. SEPARATE REAR CENTER SEAT OUTER BELT ASSEMBLY Removal (from 07/2011)
39. REMOVE ROOF HEADLINING ASSEMBLY
Text in Illustration
(a) for front pillar RH side:
(1) Disconnect the connector
(2) Using a clip remover, remove the 4 clamps.
(b) for front pillar LH side:
(1) Disconnect the connector
(2) Using a clip remover, remove the 4 clamps.
(c) for rear pillar RH side:
(1) Disconnect the connector
(2) Using a clip remover, remove the 3 clamps.
(d) Disengage the 2 claws.
(e) Using a clip remover, remove the 3 clips.
(f) Disengage the 2 hooks.
(g) Remove the roof headlining from the vehicle through the back door as shown in the illustration.
NOTICE:
Do not damage the roof headlining assembly or body interior.