Hatchback without VSC (from 07/2011)

SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for Hatchback without VSC): B1650/32: Occupant Classification System Malfunction
B1650/32 - Occupant Classification System Malfunction

DESCRIPTION

The occupant classification system circuit consists of the airbag sensor assembly and occupant classification system.

If the airbag sensor assembly receives signals from the occupant detection ECU, it determines whether the front passenger airbag, front passenger side knee airbag and front seat belt pretensioner RH should be operated.

DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.





WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CHECK DTC (OCCUPANT DETECTION ECU)

(a) Turn the ignition switch to ON.

(b) Check for DTCs of the occupant detection ECU Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC is not output.

NG -- REPAIR CIRCUITS INDICATED BY OUTPUT DTCS How To Proceed With Troubleshooting
OK -- Continue to next step.

2. CHECK CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connectors are properly connected to the airbag sensor assembly and occupant detection ECU. Also check that the connectors that link the floor wire and front seat wire RH are properly connected.

OK:

The connectors are properly connected.

HINT
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

(d) Disconnect the connectors from the airbag sensor assembly and occupant detection ECU. Also disconnect the connectors that link the floor wire and front seat wire RH.

(e) Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.

NG -- REPLACE WIRE HARNESS
OK -- Continue to next step.

3. CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)

(a) Connect the connectors that link the floor wire and front seat wire RH.





Text in Illustration





(b) Using the service wire, connect terminals 12 (FSR+) and 13 (FSR-) of connector B.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- CHECK FLOOR WIRE (OPEN)
OK -- Continue to next step.

4. CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)

(a) Disconnect the service wire from connector B.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- CHECK FLOOR WIRE (SHORT)
OK -- Continue to next step.

5. CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)

(a) Connect the cable to the negative (-) battery terminal.





(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





NG -- CHECK FLOOR WIRE (SHORT TO B+)
OK -- Continue to next step.

6. CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)

(a) Turn the ignition switch off.





(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- CHECK FLOOR WIRE (SHORT TO GROUND)

OK -- REPLACE AIRBAG SENSOR ASSEMBLY Removal (from 07/2011)

7. CHECK FLOOR WIRE (OPEN)

(a) Disconnect the front seat wire RH from the floor wire.





Text in Illustration





HINT
The service wire has already been inserted into connector B.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE

OK -- REPLACE FRONT SEAT WIRE RH

8. CHECK FLOOR WIRE (SHORT)

(a) Disconnect the front seat wire RH from the floor wire.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPLACE FLOOR WIRE

OK -- REPLACE FRONT SEAT WIRE RH

9. CHECK FLOOR WIRE (SHORT TO B+)

(a) Turn the ignition switch off.





(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Disconnect the front seat wire RH from the floor wire.

(d) Connect the cable to the negative (-) battery terminal.

(e) Turn the ignition switch to ON.

(f) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





NG -- REPLACE FLOOR WIRE

OK -- REPLACE FRONT SEAT WIRE RH

10. CHECK FLOOR WIRE (SHORT TO GROUND)

(a) Disconnect the front seat wire RH from the floor wire.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPLACE FLOOR WIRE

OK -- REPLACE FRONT SEAT WIRE RH