Removal

REAR SUSPENSION: REAR AXLE BEAM: REMOVAL

1. REMOVE REAR WHEELS

2. REMOVE FRONT UPPER CONSOLE BOX Removal

3. LOOSEN PARKING BRAKE CABLE Removal

4. REMOVE PARKING BRAKE LEVER PROTECTOR (for LH Side) Removal

5. REMOVE PARKING BRAKE LEVER PROTECTOR (for RH Side)

HINT
Perform the same procedure as the LH side.

6. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY Removal

7. DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT
Perform the same procedure as the No. 3 parking brake cable assembly.

8. DISCONNECT REAR SPEED SENSOR WIRE LH Removal

9. DISCONNECT REAR SPEED SENSOR WIRE RH

HINT
Perform the same procedure as the LH side.

10. SEPARATE REAR SPEED SENSOR WIRE LH

(a) Remove the bolt.





(b) Disengage the clamp and separate the rear speed sensor wire LH from the rear axle beam.

11. SEPARATE REAR SPEED SENSOR WIRE RH

HINT
Perform the same procedure as the LH side.

12. SEPARATE REAR FLEXIBLE HOSE LH

(a) Remove the bolt and separate the rear flexible hose LH from the rear axle beam.





13. SEPARATE REAR FLEXIBLE HOSE RH

HINT
Perform the same procedure as the LH side.

14. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH Replacement

15. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

16. REMOVE REAR DISC LH Removal

17. REMOVE REAR DISC RH

HINT
Perform the same procedure as the LH side.

18. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH Removal

19. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

20. REMOVE REAR AXLE BEAM DAMPER Removal

21. REMOVE REAR STABILIZER BAR Removal

22. SEPARATE REAR SHOCK ABSORBER WITH COIL SPRING LH





(a) Support the rear axle beam assembly using a jack and wooden block.

NOTICE:
Do not excessively jack up the rear axle beam assembly.

(b) Remove the nut and rear No. 1 shock absorber retainer.

(c) Separate the rear shock absorber with coil spring LH (lower side).

23. SEPARATE REAR SHOCK ABSORBER WITH COIL SPRING RH

HINT
Perform the same procedure as the LH side.

24. REMOVE REAR AXLE BEAM ASSEMBLY

(a) Support the rear axle beam assembly using 2 jacks and 2 wooden blocks.





(b) Remove the 2 bolts, 2 nuts, and rear axle beam assembly.





NOTICE:
Since stopper nuts are used, loosen the bolts.

25. REMOVE REAR AXLE CARRIER BUSHING LH





(a) Place matchmarks on the 2 notches of the rear axle carrier bushing and rear axle beam assembly.

(b) Using a chisel and hammer, bend the 2 portions of the rear axle carrier bushing rib.

NOTICE:
* When removing the rear axle carrier bushing, do not erase the matchmarks on the rear axle beam assembly.
* If the axle beam has been scratched, apply paint to the axle beam assembly.

(c) Using SST, remove the rear axle carrier bushing from the rear axle beam assembly.

SST : 09950-40011

09951-04020

09952-04010

09953-04030

09954-04020

09955-04051

09957-04010

09958-04011

SST : 09950-60010

09951-00630

26. REMOVE REAR AXLE CARRIER BUSHING RH

HINT
Perform the same procedure as the LH side.