Short in Front Passenger Side Squib 2nd Step Circuit - Airbag System (for TMC Made)
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM (for TMC Made): B1815/54-B1818/54: Short in Front Passenger Side Squib 2nd Step Circuit
B1818/54 - Short to B+ in Front Passenger Side Squib 2nd Step Circuit
DESCRIPTION
The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib 2nd step circuit.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT
* Perform the simulation method by selecting "check mode" (signal check) with Techstream Check Mode Procedure.
* After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road Check Mode Procedure.
PROCEDURE
1. CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB 2ND STEP)
(a) Turn the ignition switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the front passenger airbag assembly.
(d) Connect SST (resistance 2.1 Ohms) to connector E (black connector).
CAUTION:
Never connect the tester to the front passenger airbag assembly (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.
NOTICE:
* Do not forcibly insert the SST into the terminals of the connector when connecting.
* Insert straight the SST into the terminals of the connector.
SST : 09843-18061
(e) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(f) Turn the ignition switch on (IG), and wait for at least 60 seconds.
(g) Clear the DTCs stored in the memory Airbag System (for TMC Made).
(h) Turn the ignition switch off.
(i) Turn the ignition switch on (IG), and wait for at least 60 seconds.
(j) Check the DTCs Airbag System (for TMC Made).
OK:
DTC B1815, B1816, B1817, B1818, or 54 is not output.
HINT
Codes other than DTC B1815, B1816, B1817, B1818, and 54 may be output at this time, but they are not related to this check.
OK -- REPLACE FRONT PASSENGER AIRBAG ASSEMBLY Removal
NG -- Continue to next step.
2. CHECK CONNECTOR
(a) Turn the ignition switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect SST from connector E.
(d) Check that the instrument panel wire assembly connectors (on the front passenger airbag assembly side) are not damaged.
OK:
The lock button is not disengaged, or the claw of the lock is not damaged or deformed.
NG -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK -- Continue to next step.
3. CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT
(a) Disconnect the connectors from the center airbag sensor assembly.
(b) Check for a short to B+ in the circuit.
(1) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(2) Turn the ignition switch on (IG).
(3) Measure the voltage according to the value(s) in the table below.
Standard voltage:
(c) Check for an open in the circuit.
(1) Turn the ignition switch off.
(2) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(3) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(d) Check for a short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(e) Check for a short in the circuit.
(1) Release the activation prevention mechanism built into connector B Diagnosis System.
(2) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- CHECK INSTRUMENT PANEL WIRE
OK -- Continue to next step.
4. CHECK CENTER AIRBAG SENSOR ASSEMBLY
(a) Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in the memory Airbag System (for TMC Made).
(e) Turn the ignition switch off.
(f) Turn the ignition switch on (IG), and wait for at least 60 seconds.
(g) Check the DTCs Airbag System (for TMC Made).
OK:
DTC B1815, B1816, B1817, B1818, or 54 is not output.
HINT
Codes other than DTC B1815, B1816, B1817, B1818, and 54 may be output at this time, but they are not related to this check.
NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal
OK -- USE SIMULATION METHOD TO CHECK Diagnosis System
5. CHECK INSTRUMENT PANEL WIRE
(a) Check for a short to B+ in the circuit.
(1) Restore the released activation prevention mechanism of connector B to the original condition.
(2) Disconnect the instrument panel wire connector from the instrument panel wire assembly.
(3) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(4) Turn the ignition switch on (IG).
(5) Measure the voltage according to the value(s) in the table below.
Standard voltage:
(b) Check for an open in the circuit.
(1) Turn the ignition switch off.
(2) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(3) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(c) Check for a short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(d) Check for a short in the circuit.
(1) Release the activation prevention mechanism built into connector B Diagnosis System.
(2) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK -- Continue to next step.
6. CHECK INSTRUMENT PANEL WIRE ASSEMBLY
(a) Check for a short to B+ in the circuit.
(1) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(2) Turn the ignition switch on (IG).
(3) Measure the voltage according to the value(s) in the table below.
Standard voltage:
(b) Check for an open in the circuit.
(1) Turn the ignition switch off.
(2) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(3) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(c) Check for a short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(d) Check for a short in the circuit.
(1) Release the activation prevention mechanism built into connector D Diagnosis System.
(2) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK -- USE SIMULATION METHOD TO CHECK Diagnosis System