Parking Brake Cable: Service and Repair
PARKING BRAKE CABLECOMPONENTS:
REMOVAL
HINT: For parking brake cable assembly No. 2, perform the same procedure to the parking brake cable assembly No. 3.
1. REMOVE REAR WHEEL
2. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)
3. REMOVE FRONT BRAKE SHOE (for Drum Type)
4. REMOVE PARKING BRAKE SHOE STRUT SET LH
5. REMOVE REAR BRAKE AUTOMATIC ADJUST LEVER LH (for Drum Type)
6. REMOVE REAR BRAKE SHOE (for Drum Type)
7. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH (for Disc Type)
8. REMOVE REAR DISC (for Disc Type)
9. REMOVE PARKING BRAKE SHOE STRUT LH (for Disc Type)
10. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET (for Disc Type)
11. REMOVE PARKING BRAKE SHOE ASSEMBLY LH NO. 1 (for Disc Type)
12. REMOVE PARKING BRAKE SHOE ASSEMBLY LH NO. 2 (for Disc Type)
13. REMOVE PARKING BRAKE SHOE LEVER LH (for Disc Type)
14. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO. 3
(a) Remove the bolt, and disconnect the parking brake cable assembly No. 3 from the backing plate.
15. REMOVE EXHAUST PIPE ASSEMBLY FRONT
16. REMOVE FRONT FLOOR HEAT INSULATOR NO. 1
17. REMOVE FRONT FLOOR HEAT INSULATOR NO. 2
18. REMOVE FUEL TANK PROTECTOR NO. 1
(a) Remove the 5 nuts and fuel tank protector No. 1.
19. REMOVE PARKING BRAKE CABLE ASSEMBLY NO. 3
(a) Using a clip remover, disconnect the skid control sensor wire harness clip from the clamp.
(b) Remove the 4 bolts and cable retainer from the body.
(c) Disconnect the parking brake cable assembly No. 3 from the equalizer, and remove the parking brake cable assembly No. 3.
INSTALLATION
1. INSTALL PARKING BRAKE CABLE ASSEMBLY NO. 3
(a) Connect the parking brake cable assembly No. 3 to the equalizer.
(b) Install the parking brake cable assembly No. 3 with the 4 bolts and cable retainer.
Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
(c) Connect the skid control sensor wire harness clip to the clamp.
2. INSTALL FUEL TANK PROTECTOR NO. 1
(a) Install the fuel tank protector No. 1 with the 5 nuts.
Torque: 5.5 N*m (55 kgf*cm, 48 in.*lbf)
3. INSTALL FRONT FLOOR HEAT INSULATOR NO. 2
4. INSTALL FRONT FLOOR HEAT INSULATOR NO. 1
5. INSTALL EXHAUST PIPE ASSEMBLY FRONT
6. CONNECT PARKING BRAKE CABLE ASSEMBLY NO. 3
(a) Connect the parking brake cable assembly No. 3 to the backing plate with the bolt.
Torque: 7.8 N*m (80 kgf*cm, 69 in.*lbf)
7. APPLICATION HIGH TEMPERATURE GREASE (for Drum Type)
8. INSTALL REAR BRAKE SHOE (for Drum Type)
9. INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER LH (for Drum Type)
10. INSTALL PARKING BRAKE SHOE STRUT SET LH (for Drum Type)
11. INSTALL FRONT BRAKE SHOE (for Drum Type)
12. CHECK REAR DRUM BRAKE INSTALLATION
13. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)
14. ADJUST REAR DRUM BRAKE SHOE CLEARANCE (for Drum Type)
15. APPLICATION HIGH TEMPERATURE GREASE (for Disc Type)
16. INSTALL PARKING BRAKE SHOE LEVER LH (for Disc Type)
17. INSTALL PARKING BRAKE SHOE ASSEMBLY LH NO. 2 (for Disc Type)
18. INSTALL PARKING BRAKE SHOE ASSEMBLY LH NO. 1 (for Disc Type)
19. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET (for Disc Type)
20. INSTALL PARKING BRAKE SHOE STRUT LH (for Disc Type)
21. CHECK PARKING BRAKE INSTALLATION (for Disc Type)
22. INSTALL REAR DISC (for Disc Type)
23. ADJUST PARKING BRAKE SHOE CLEARANCE (for Disc Type)
24. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH (for Disc Type)
25. INSTALL REAR WHEEL
Torque: 103 N*m (1,050 kgf*cm, 76 ft.*lbf)
26. INSPECT PARKING BRAKE LEVER TRAVEL
27. ADJUST PARKING BRAKE LEVER TRAVEL
28. CHECK EXHAUST LEAKAGE