Rear NO.1
REAR SUSPENSION ARM ASSY NO.1 LH REPLACEMENTHINT: This procedure is provided for the replace on the LH side. Replace the other side in the same way.
1. REMOVE REAR WHEEL
2. REMOVE EXHAUST PIPE ASSEMBLY
a. 1MZ-FE engine:
Remove the exhaust pipe assembly.
b. 2AZ-FE engine:
Remove the exhaust pipe assembly.
3. REMOVE PROPELLER W/CENTER BEARING SHAFT ASSY
SST 09325-20010
4. REMOVE STRUT ROD ASSY REAR
5. SEPARATE REAR SUSPENSION ARM ASSY NO.2 LH
a. Remove the bolt, nut and rear suspension arm No. 2 (outer side) from rear axle carrier.
HINT: While fixing the nut, turn and remove the bolt.
6. SEPARATE REAR SUSPENSION ARM ASSY NO.2 RH
HINT: Separate the RH side by the same procedures with the LH side.
7. SEPARATE REAR SUSPENSION ARM ASSY NO.1 LH
a. Remove the bolt, nut and rear suspension arm No. 1 (outer side) from rear axle carrier.
HINT: While fixing the nut, turn and remove the bolt.
8. SEPARATE REAR SUSPENSION ARM ASSY NO.1 RH
HINT: Separate the RH side by the same procedures with the LH side.
9. REMOVE SPEED SENSOR REAR LH
10. REMOVE SPEED SENSOR REAR RH
HINT: Remove the RH side by the same procedures with the LH side.
11. REMOVE REAR DRIVE SHAFT ASSY LH
12. REMOVE REAR DRIVE SHAFT ASSY RH
HINT: Remove the RH side by the same procedures with the LH side.
13. REMOVE REAR SUSPENSION MEMBER SUB-ASSY
a. Support the rear suspension member with a jack.
b. Remove the 4 nuts, 2 bolts and 2 retainers from the rear suspension member.
14. REMOVE REAR SUSPENSION ARM ASSY NO.1 LH
a. Lower the rear suspension member.
b. Remove the bolt, nut and lower suspension arm No. 1.
15. TEMPORARY TIGHTEN REAR SUSPENSION ARM ASSY NO.1 LH
a. Install the lower suspension No. 1 with the bolt, nut and temporarily tighten the bolt.
b. Set suspension arm in the Position shown in the illustration and fully tighten the bolt.
Torque: 113 Nm (1,150 kgf-cm, 83 ft. lbs.)
16. INSTALL REAR SUSPENSION MEMBER SUB-ASSY
a. Support the rear suspension member with a jack.
b. Install the rear suspension member with the 4 nuts, 2 bolts and 2 retainers.
Torque:
Front side: 115 Nm (1,173 kgf-cm, 85 ft. lbs.)
Rear side: 181 Nm (1,850 kgf-cm, 134 ft. lbs.)
17. INSTALL REAR DRIVE SHAFT ASSY LH
18. INSTALL REAR DRIVE SHAFT ASSY RH
HINT: Install the RH side by the same procedures with the LH side.
19. INSTALL SPEED SENSOR REAR LH
20. INSTALL SPEED SENSOR REAR RH
HINT: Install the RH side by the same procedures with the LH side.
21. INSTALL REAR SUSPENSION ARM ASSY NO.1 LH
a. Install the rear suspension arm No. 1 (out side) to the rear axle carrier with the bolt and nut.
Torque: 177 Nm (1,800 kgf-cm, 131 ft. lbs.)
HINT: Insert the bolt from the front side of the vehicle and temporarily install the bolt.
22. INSTALL REAR SUSPENSION ARM ASSY NO.1 RH
HINT: Install the RH side by the same procedures with the LH side.
23. INSTALL REAR SUSPENSION ARM ASSY NO.2 LH
a. Install the rear suspension arm No. 2 (out side) to the rear axle carrier with the bolt and nut.
Torque: 177 Nm (1,800 kgf-cm, 131 ft. lbs.)
24. INSTALL REAR SUSPENSION ARM ASSY NO.2 RH
HINT: Install the RH side by the same procedures with the LH side.
25. TEMPORARY TIGHTEN STRUT ROD ASSY REAR
26. STABILIZE THE SUSPENSION
27. FULLY TIGHTEN STRUT ROD ASSY REAR
28. INSTALL REAR WHEEL
Torque: 103 Nm (1,050 kgf-cm, 76 ft. lbs.)
29. TEMPORARY TIGHTEN PROPELLER W/CENTER BEARING SHAFT ASSY
30. FULLY TIGHTEN PROPELLER W/CENTER BEARING SHAFT ASSY
31. INSTALL EXHAUST PIPE ASSEMBLY
a. 1MZ-FE engine:
Install the exhaust pipe assembly.
b. 2AZ-FE engine:
Install the exhaust pipe assembly.
32. CHECK GAS LEAKAGE ON EXHAUST SYSTEM
33. INSPECT REAR WHEEL ALIGNMENT
34. CHECK ABS SPEED SENSOR SIGNAL