With Subaru Select Monitor
OPERATIONREAD DIAGNOSTIC TROUBLE CODE (DTC)
1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Insert the cartridge to Subaru Select Monitor.
4. Connect the Subaru Select Monitor to data link connector.
1 Data link connector is located in the lower portion of the instrument panel (on the driver's side).
2 Connect the diagnosis cable to data link connector.
CAUTION: Do not connect the scan tools except for Subaru Select Monitor.
5. Turn the ignition switch to ON (engine OFF) and turn the Subaru Select Monitor switch to ON.
6. On the [[Main Menu]] display screen, select the {Each System Check} and press the [YES] key.
7. On the [[System Selection Menu]] display screen, select the {Brake Control} and press the [YES] key.
8. Press the [YES] key after the {ABS} is displayed.
9. On the [[ABS Diagnosis]] display screen, select the {DTC Display} and press the [YES] key.
NOTE:
^ For details concerning operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
^ For details concerning DTCs, refer to the "List of Diagnostic Trouble Code (DTC)".
^ DTCs are displayed up to three in detected order.
^ If a particular DTC is not properly stored in memory (due to a drop in ABSCM&H/U power supply, etc.) on the occurrence of a problem, the DTC which is suffixed with a question mark "?" appears on the Subaru Select Monitor display. This shows it may be an unreliable reading.
10. If ABS and Subaru Select Monitor cannot communicate, check the communication circuit.
11. When DTC is not displayed, check the meter circuit or CAN communication circuit.
READ CURRENT DATA
1. On the [[Main Menu]] display screen, select the {Each System Check} and press the [YES] key.
2. On the [[System Selection Menu]] display screen, select the {Brake Control} and press the [YES] key.
3. Press the [YES] key after the {ABS} is displayed.
4. On the [[Brake Control Diagnosis]] screen, select the {Current Data Display/Save}, and then press the [YES] key.
5. On the [[Data Display Menu]] screen, select the data display style and press the [YES] key.
6. Using a scroll key, move the display screen up or down until necessary data is shown.
^ A list of the support data is shown in the following table.
NOTE: For details concerning operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
CLEAR MEMORY MODE
1. On the [[Main Menu]] display screen, select the {2. Each System Check} and press the [YES] key.
2. On the [[System Selection Menu]] display screen, select the {Brake Control} and press the [YES] key.
3. Press the [YES] key after the {ABS} is displayed.
4. On the [[Brake Control Diagnosis]] display screen, select the {Clear Memory} and press the [YES] key.
5. When "Done" and "Turn ignition switch OFF" are shown on the display screen, turn the Subaru Select Monitor and ignition switch to OFF.
NOTE: For details concerning operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
ABS SEQUENCE CONTROL
FREEZE FRAME DATA
NOTE:
^ Data stored at the time of trouble occurrence is shown on display.
^ Each time trouble occurs, the latest information is stored in the freeze frame data in memory.
^ Freeze frame data will be memorized up to three.
^ If a Freeze Frame Data is not properly stored in memory (due to a drop in ABS control module power supply, etc.), the DTC which is suffixed with a question mark "?" appears on the Subaru Select Monitor display. This shows it may be an unreliable reading.
INSPECTION
COMMUNICATION FOR INITIALIZING IMPOSSIBLE
DETECTING CONDITION: Defective harness connector
TROUBLE SYMPTOM: Communication is impossible between ABS and Subaru Select Monitor.
WIRING DIAGRAM
WITHOUT DTC
DETECTING CONDITION:
^ Defective combination meter
^ Open in harness
TROUBLE SYMPTOM:
^ ABS warning light does not go off.
^ "NO TROUBLE CODE" will be displayed on the Subaru Select Monitor.
NOTE: When the ABS warning light is OFF and "NO TROUBLE CODE" is displayed on Subaru Select Monitor, the system is in normal condition.
WIRING DIAGRAM