Basic Diagnostics Procedure
6A1: CHECK KEYLESS ENTRY FUNCTION.1. Perform pre-inspection.
2. Remove ignition key from ignition switch.
3. Set the room light switch in the middle position.
4. Close all doors, rear gate and trunk lid.
5. Press the LOCK/ARM button one time.
CHECK: Do all doors and rear gate lock normally?
YES: Go to step 6A2.
NO: Replace keyless entry control module.
6A2: CHECK KEYLESS ENTRY FUNCTION.
Check if the horn signal chirps.
CHECK: Does the horn chirp one time?
YES: Go to step 6A3.
NO: go to step 6B1.
6A3: CHECK KEYLESS ENTRY FUNCTION.
Press the UNLOCK/DISARM button one time.
CHECK: Does the driver's's door unlock normally?
YES: Go to step 6A4.
NO: Replace keyless entry control module.
6A4: CHECK KEYLESS ENTRY FUNCTION.
Check if the horn signal chirps.
CHECK: Does the horn chirp two times?
YES: Go to step 6A5.
NO: Replace keyless entry control module.
6A5: CHECK KEYLESS ENTRY FUNCTION.
Check if the room light is turned on.
CHECK: Does the room light turn on for 30 seconds, and then turn off?
YES: Go to step 6A6.
NO: Go to step 6C1.
6A6: CHECK KEYLESS ENTRY FUNCTION.
1. Press the LOCK/ARM button one time.
2. Press the UNLOCK/DISARM button two times.
CHECK: Do all doors and rear gate unlock normally?
YES: Go to step 6A7.
NO: Replace keyless entry control module.
6A7: CHECK KEYLESS ENTRY FUNCTION.
Keep the LOCK/ARM button pressed for more than 1.5 seconds.
CHECK: Does the horn sound for 30 seconds, and then turns off?
YES: Go to step 6A8.
NO: Replace keyless entry control module.
6A8: CHECK KEYLESS ENTRY FUNCTION.
1. Keep the LOCK/ARM button pressed for more than 1.5 seconds.
2. Horn will sound, and then press the LOCK/ARM button.
CHECK: Does the horn turn off?
YES: Go to step 6A9.
NO: Replace keyless entry control module.
6A9: CHECK KEYLESS ENTRY FUNCTION.
1. Keep the LOCK/ARM button pressed for more than 1.5 seconds.
2. Horn will sound, and then press the UNLOCK/DISARM button.
CHECK: Does the horn turn off?
YES: Go to step 6A10.
NO: Replace keyless entry control module.
6A10: CHECK DOOR SWITCH FUNCTION.
Open the front left door.
CHECK: Does the room light turn on?
YES: Go to step 6A11.
NO: Go to step 6D1.
6A11: CHECK DOOR SWITCH FUNCTION.
1. Close the front left door.
2. Open the front right door.
CHECK: Does the room light turn on?
YES: Go to step 6A12.
NO: Go to step 6D1.
6A12: CHECK DOOR SWITCH FUNCTION.
1. Close the front right door.
2. Open the rear left door.
CHECK: Does the room light turn on?
YES: Go to step 6A13.
NO: Go to step 6D1.
6A13: CHECK DOOR SWITCH FUNCTION.
1. Close the rear left door.
2. Open the rear right door.
CHECK: Does the room light turn on?
YES: Go to step 6A14.
NO: Go to step 6D1.
6A14: PERFORM PROGRAMMING.
NOTE: Finish operation from step 1. through 4. within 45 seconds.
1. Sit on the driver's seat and close all doors, rear gate and trunk lid.
2. Open the driver's door.
3. Close the driver's door.
4. Turn the ignition switch from ON to LOCK ten times in rapid succession (within 15 seconds).
NOTE: Do not start the engine at this time.
5. The horn chirps one time to indicate that the system has been in the programming mode.
6. Open the driver's door.
7. Close the driver's door.
8. Press any button on the transmitter that you wish to program into the system.
9. Horn will chirp two times to indicate that the transmitter has been programmed.
NOTE: Any additional transmitter can also be programmed at this time. Repeat steps 6. through 9. for an additional transmitter.
10. Remove the ignition key from the ignition switch.
11. The horn will chirp three times to indicate that the system has exited the programming mode.
12. Check the key ass entry system properly operates by operating each transmitter.
CHECK: Does the transmitter operate normally?
YES: Go to step 6A15.
NO: Go to step 6E1.
6A15: CHECK IGNITION KEY SWITCH.
1. Insert the ignition key to the ignition switch (at LOCK position).
2. Perform lock and unlock with transmitter.
CHECK: Does the power door lock function normally?
YES: Go to step 6F1.
NO: End of basic diagnostics procedure.