AZ82.20-P-0010-01MCC Retrofit Ambiance Illumination Wiring Harness

AZ82.20-P-0010-01MCC Retrofit Ambiance Illumination Wiring Harness

000 589 13 99 00, Wiring harness repair kit, basic












Connection diagram
1 Inside rearview mirror ambiance illumination
2 Footwell ambiance illumination
3 Footwell entrance illumination
5 Coupling "N11-5"
5.8 Pin
6 Black, 2-pin coupling
7 Black 2-pin connector
8 Coupling "N11-8"
8.4 Pin
8.19 Pin
9 Black, 2-pin coupling
10 Black 2-pin connector
11 Black, 2-pin coupling
12 Black 2-pin connector
13 Black, 2-pin coupling
14 Black 2-pin connector
15 Fuse carrier with fuse
16 Ambiance illumination wiring harness
N10/10 SAM control unit
W14 Left floor interior compartment ground
br Brown wire
br/gr Brown/gray line
ge/sw Yellow/black line
ge/ws Yellow/white line
gn/bl Gray/blue line
rt Red line

The dashed brown/gray line (br/gr), yellow/black line (ge/sw) and yellow/white line (ge/ws) show the original installation of lines in the vehicle; the continuous lines show the retrofit.
The black continuous lines show the adapter lines.







Routing diagram
16 Ambiance illumination wiring harness
N10/10 SAM control unit







1. Route inside rearview mirror ambiance illumination branch-off line of ambiance illumination wiring harness (16) from SAM control unit (N10/10), as shown, along vehicle wiring harness behind instrument panel (17) to top of A-pillar.
Only route the 1700 mm long branch-off line of the inside rearview mirror ambiance illumination to the top of the A-pillar.
The three black 2-pin couplings and the fuse carrier with fuse of the ambiance illumination wiring harness (16) must be located in the area of the SAM control unit (N10/10). They will be connected to the SAM control unit (N10/10) at a later point.







2. Route inside rearview mirror ambiance illumination branch-off line of ambiance illumination wiring harness (16), as shown, along vehicle wiring harness to installation location of inside rearview mirror (4).
3. Fix inside rearview mirror ambiance illumination branch-off line of ambiance illumination wiring harness (16) in place using cable tie (18) at vehicle wiring harness.
4. Slide inside rearview mirror (4) onto bracket on windshield.
5. Connect black 2-pin connector (21) of inside rearview mirror ambiance illumination wiring harness (22) to black 2-pin coupling (20) of ambiance illumination wiring harness (16).
6. Form a loop with excess length of inside rearview mirror ambiance illumination branch-off line of ambiance illumination wiring harness (16) and fix in place using cable tie (19).







7. Route footwell branch-off line of ambiance illumination wiring harness (16), as shown, along vehicle wiring harness behind instrument panel and fix in place using cable tie.
Do not tighten cable tie yet.
The black 2-pin couplings at the footwell branch-off line of ambiance illumination wiring harness (16) must be positioned centrally in the driver and front passenger footwell.







8. Release coupling "N11-5" and disconnect at SAM control unit (N10/10).
Coupling "N11-5" is located in the marked slot (arrow).







9. Unplug pin (5.8) of brown/gray line (br/gr) from slot 8 of coupling "N11-5" (5).
10. Plug pin of brown/gray line (br/gr) of adapter line into slot 8 of coupling "N11-5" (5).







11. Plug brown/gray line (br/gr) unplugged from slot 8 of coupling "N11-5" (5) into slot 1 of black 2-pin coupling (6).
12. Connect black 2-pin coupling (6) to black 2-pin connector (7) of adapter line.
13. Connect coupling "N11-5" (5) at control unit (N10/10).







14. Connect black 2-pin connector (9) of gray/blue line (gr/bl) of adapter line to black 2-pin coupling (10) of gray/blue line (gr/bl) of ambiance illumination wiring harness (16).







15. Release coupling "N11-8" and disconnect at SAM control unit (N10/10).
Coupling "N11-8" is located in the marked slot (arrow A).







16. Remove white insert (8a) from coupling "N11-8" (8).







17. Unplug pin (8.4) of yellow/white line (ge/ ws) from slot 4 of white insert (8a).
18. Plug pin of yellow/white adapter line (ge/ws) into slot 4 of white insert (8a).
19. Plug yellow/white line (ge/ws) unplugged from slot 4 of white insert (8a) into slot 4 of black 2-pin coupling (12) of yellow/ white line (ge/ws) of ambiance illumination wiring harness (16).
20. Connect black 2-pin coupling (12) of ambiance illumination wiring harness (16) to black 2-pin connector (11) of yellow/ white adapter line (ge/ws).







21. Unplug pin (8.19) of yellow/black line (ge/sw) from slot 19 of white insert (8a).
22. Plug pin of yellow/black adapter line (ge/sw) into slot 19 of white insert (8a).
23. Plug yellow/black line (ge/sw) unplugged from slot 19 of white insert (8a) into slot 19 of black 2-pin coupling (14) of yellow/ black line (ge/sw) of ambiance illumination wiring harness (16).
24. Connect black 2-pin coupling (14) of ambiance illumination wiring harness (16) to black 2-pin connector (13) of yellow/ black adapter line (ge/sw).







25. Install white insert (8a) in coupling "N11-5" (8).
26. Connect coupling "N11-5" (8) at SAM control unit.







27. Insert fuse carrier with fuse (15) at SAM control unit (N10/10).
The slot and the fuse carrier with fuse (15) are coded. The fuse has a fuse rating of 10 A.

28. Screw on brown line (br) of ambiance illumination wiring harness to left interior floor ground (W14).
29. Clip SAM control unit (N10/10) into rear area (arrow B) and screw on using screws/bolts (23).