AN82.10-P-0100-01MCC Retrofit Daytime Running Lights Headlamp Wiring Harness

AN82.10-P-0100-01MCC Retrofit Daytime Running Lights Headlamp Wiring Harness

000 589 13 99 00, Wiring harness repair kit, basic







450 589 12 37 00, Expanding pliers







450 589 25 63 00, Puller aid












Connection diagram
1 Daytime running lights headlamp
3.1 Front wiring harness
3.2 Interior compartment wiring harness
5 Coupling "N11-5"
5.8 Pin
6 Clutch
7 Connector
8 Daytime running lamp control unit
9 Clutch
12 Adapter line
13 Fuse
14 Fuse holder
15 Firewall rubber grommet
N10/10 SAM control unit
W43 Ground (outside left fire wall)
br Brown line
br/gr Brown/gray line
gn/bl Gray/blue line
rt/bl Red/blue line

The dashed brown/gray line (br/gr) shows the original installation of lines in the vehicle and the continuous lines are the retrofit.







Routing diagram for front wiring harness (3.1)
3.1 Front wiring harness
3.2 Interior compartment wiring harness
8 Daytime running lamp control unit
W43 Ground (outside left fire wall)
br Brown line







Routing diagram for interior wiring harness (3.2)
3.2 Interior compartment wiring harness
12 Adapter line
14 Fuse holder
15 Firewall rubber grommet
N10/10 SAM control unit
gn/bl Gray/blue line
rt/bl Red/blue line







1. Route front wiring harness (3.1), as shown, to vehicle-side wiring harness and temporarily fasten with cable ties.
Do not damage front wiring harness (3.1) while routing by means of crushing or pinching as this may lead to a short circuit.

Use puller aid in the area of the wiper system.

2. Lay interior wiring harness (3.2) in area of windshield washer reservoir until it is routed further.







3. Route front wiring harness (3.1), as shown, at vehicle wiring harness and guide coupling (16) through opening in front module.
Do not damage front wiring harness (3.1) while routing by means of crushing or pinching as this may lead to a short circuit.

4. Temporarily fasten front wiring harness (3.1) in illustrated area at vehicle-side wiring harness using cable ties.







5. Cut open cable duct (arrow A) of firewall rubber grommet (15).
6. Enlarge cable duct (arrow A) using expanding pliers and guide interior wiring harness (3.2) through opening into interior.
Do not damage interior wiring harness (3.2) while routing by means of crushing or pinching as this may lead to a short circuit.

7. Route interior wiring harness (3.2) and front wiring harness (3.1), as shown, at vehicle-side wiring harness and temporarily fasten using cable ties.







8. Connect brown line (br) at outer left firewall ground (W43).
9. Route brown line (br) and front wiring harness (3.1) to vehicle-side wiring harness and temporarily fasten with cable ties.







10. Route front wiring harness (3.1), as shown, at vehicle-side wiring harness and guide coupling (17) through opening in front module.
Do not damage front wiring harness (3.1) while routing by means of crushing or pinching as this may lead to a short circuit.

11. Temporarily fasten front wiring harness (3.1) in illustrated area at vehicle-side wiring harness using cable ties.
12. Check routing of front wiring harness (3.1) and tighten all cable ties used, then shorten excess length of cable ties.







Operation steps 13 to 18 only on vehicles without retrofitted ambiance illumination.

13. Release and disconnect coupling "N11-5" at SAM control unit (N10/10).
Coupling "N11-5" is located in the marked slot (arrow).







14. Detach pin (5.8) of brown/gray line (br/gr) from slot 8 of coupling "N11-5" (5) with wiring harness repair kit, basic.
15. Plug pin (4) of brown/gray line (br/gr) of adapter line (12) into slot 8 of coupling "N11-5" (5).







16. Unlatch secondary lock (10) of coupling (9) and carefully pull out of coupling (9) up to end stop.
17. Plug pin (5.8) of brown/gray line (br/gr) into slot 1 of coupling (9).
Brown/gray line (br/gr) can be guided through closed cap (arrow D) and through seal (11).

18. Slide secondary lock (10) into coupling (9) until it engages.







19. Plug gray/blue line (gr/bl) of interior wiring harness into slot 1 of coupling (6).
On vehicles with retrofitted ambiance illumination, the gray/ blue line (gr/bl) must be crimped with gray/blue line (gr/bl) of adapter line already installed.

20. Plug red/blue line (rt/bl) of interior wiring harness into fuse holder (14).
Ensure that fuse (13) is seated correctly.

21. Insert fuse holder (14) in one of the suitably coded slots "R1" to "R4" (arrow B) at SAM control unit (N10/10).







Operation steps 22 to 24 only on vehicles without retrofitted ambiance illumination.

22. Connect coupling (9) with connector of adapter line (12).
23. Connect coupling (6) with connector (7) of adapter line (12).
24. Insert coupling "N11-5" (5) into slot (arrow C) at SAM control unit (N10/10).







Operation steps 25 to 28 only on vehicles with retrofitted ambiance illumination.

25. Separate gray/blue line (gr/bl) of adapter line (12).
Do not separate the gray/blue line (gr/bl) of the ambiance illumination wiring harness connected to the adapter line (12).

26. Slide heat-shrinkable tube over gray/ blue line (gr/bl) of adapter line (12).







27. Crimp together gray/blue line (gr/bl) of adapter line (12) and gray/blue line (gr/bl) of front wiring harness (3.1).
28. Protect crimped connection (18) with heat-shrinkable tube.
29. Fasten wiring harnesses of SAM control unit (N10/10) using cable tie (2), as shown, and then shorten excess length of cable tie (2).