B1907

SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1905/74-B1908/74:

B1907/74 - Short to GND in Front Pretensioner Squib LH Circuit

DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor assembly and the front seat outer belt assembly LH.

This circuit signals the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front pretensioner squib LH circuit.





WIRING DIAGRAM





INSPECTION PROCEDURE

HINT
* Perform the simulation method by selecting Check Mode (signal check) with the Techstream Check Mode Procedure.
* After selecting Check Mode (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city street or rough road Diagnosis System.

PROCEDURE

1. CHECK CONNECTOR

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check that the connector is properly connected to the front seat outer belt assembly LH.

OK:

The connector is properly connected.

HINT
If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

(d) Disconnect the connector from the front seat outer belt assembly LH.

(e) Check that the floor wire connector (on the front seat outer belt assembly LH side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.

NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

2. CHECK DTC





SST : 09843-18061

(a) Disconnect the connectors from the front seat outer belt assembly LH.

(b) Connect SST (resistance 2.1 Ohms) to connector C.

CAUTION:
Never connect a tester to the front seat outer belt assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
* Do not forcibly insert SST into the terminals of the connector when connecting.
* Insert SST straight into the terminals of the connector.

(c) Connect the cable to the negative battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs stored in the memory Reading and Clearing Diagnostic Trouble Codes.

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check the DTCs Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC B1905, B1906, B1907, B1908 or 74 is not output.

Text in Illustration





HINT
DTCs other than B1905, B1906, B1907, B1908 and 74 may be output at this time, but they are not related to this check.

NG -- CHECK CONNECTOR

OK -- REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH) Removal

3. CHECK CONNECTOR

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Disconnect the SST from connector C.

(d) Check that the connector is properly connected to the center airbag sensor assembly.

OK:

The connector is properly connected.

HINT
If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

(e) Disconnect the connector from the center airbag sensor assembly.

(f) Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.

(g) Check that the short spring for the floor wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.

NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

4. CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH - CENTER AIRBAG SENSOR ASSEMBLY)





(a) Connect the cable to the negative battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(f) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





(g) Release the activation prevention mechanism built into connector B Diagnosis System.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





(i) Restore the released activation prevention mechanism of connector B to the original condition.

NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

5. CHECK DTC

(a) Connect the connectors to the front seat outer belt assembly LH and the center airbag sensor assembly.

(b) Connect the cable to the negative battery terminal, and wait for at least 2 seconds.

(c) Turn the ignition switch to ON, and wait for at least 60 seconds.

(d) Clear the DTCs stored in the memory Reading and Clearing Diagnostic Trouble Codes.

(e) Turn the ignition switch off.

(f) Turn the ignition switch to ON, and wait for at least 60 seconds.

(g) Check the DTCs Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC B1905, B1906, B1907, B1908 or 74 is not output.

HINT
DTCs other than B1905, B1906, B1907, B1908 and 74 may be output at this time, but they are not related to this check.

NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal

OK -- USE SIMULATION METHOD TO CHECK Diagnosis System