Installation
AXLE: REAR AXLE HUB: INSTALLATION
HINT
* Use the same procedures for the RH and LH side.
* The procedures listed below are for the LH side.
* A bolt without a torque specification is shown in the standard bolt chart Standard Bolt - Specified Torque For Standard Bolts.
1. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY
(a) Install the hub and bearing assembly and back plate assembly to the rear axle carrier with the 4 bolts and nut.
Torque : 56 Nm (571 kgf-cm, 41 ft-lbf for bolt)
Torque : 140 Nm (1428 kgf-cm, 103 ft-lbf for nut)
2. TEMPORARILY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY
(a) Temporarily tighten the upper control arm with the bolt and nut.
HINT
Insert the bolt from the rear side of the vehicle and temporarily install the bolt.
3. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY
(a) Temporarily tighten the rear suspension arm (ball joint side) with the bolt and nut.
HINT
Insert the bolt from the rear side of the vehicle and temporarily install the bolt.
4. TEMPORARILY TIGHTEN LOWER CONTROL ARM ASSEMBLY
(a) Temporarily tighten the lower control arm with the nut.
5. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
(a) Install the No. 3 parking brake cable to the backing plate with the bolt.
Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)
6. APPLY HIGH TEMPERATURE GREASE
(a) Apply high temperature grease Reassembly.
7. INSTALL PARKING BRAKE SHOE LEVER
(a) Install the parking brake shoe lever Reassembly.
8. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY
(a) Install the No. 1 parking brake shoe assembly Reassembly.
9. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET
(a) Install the parking braking brake shoe adjusting screw set Reassembly.
10. INSTALL PARKING BRAKE SHOE STRUT
(a) Install the parking brake shoe strut Reassembly.
11. CHECK PARKING BRAKE INSTALLATION
(a) Check the parking brake installation Reassembly.
12. INSPECT AXLE HUB BEARING BACKLASH
(a) Inspect the axle hub bearing backlash Rear Axle Hub.
13. INSPECT AXLE HUB BEARING DEVIATION
(a) Inspect the axle hub bearing deviation Rear Axle Hub.
14. INSTALL REAR DISC
15. ADJUST PARKING BRAKE SHOE CLEARANCE
(a) Adjust the parking brake shoe clearance Installation.
16. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY
(a) Install the rear disc brake caliper with the 2 bolts.
Torque : 47 Nm (475 kgf-cm, 34 ft-lbf)
17. CONNECT SKID CONTROL SENSOR WIRE
(a) Connect the skid control sensor wire with the bolt.
Torque : 5.0 Nm (51 kgf-cm, 44 in-lbf)
(b) Connect the connector.
HINT
Do not twist the sensor wire when installing the sensor.
18. INSTALL REAR WHEEL
Torque : 103 Nm (1050 kgf-cm, 76 ft-lbf)
19. STABILIZE SUSPENSION
(a) Stabilize the suspension Installation.
20. FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY
(a) Fully tighten the bolt and nut.
Torque : 74 Nm (755 kgf-cm, 55 ft-lbf)
NOTICE:
When installing the bolt, hold the nut in place.
21. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY
(a) Fully tighten the nut (ball joint side).
Torque : 105 Nm (1071 kgf-cm, 77 ft-lbf)
(b) Install a new clip.
NOTICE:
If the holes for the clip are not aligned, tighten the nut an additional 60°.
(c) Fully tighten the bolt and nut.
Torque : 74 Nm (755 kgf-cm, 55 ft-lbf)
NOTICE:
When installing the bolt, hold the nut in place.
22. FULLY TIGHTEN LOWER CONTROL ARM ASSEMBLY
(a) Fully tighten the nut.
Torque : 105 Nm (1071 kgf-cm, 77 ft-lbf)
(b) Install a new cotter pin.
NOTICE:
If the holes for the clip are not aligned, tighten the nut an additional 60°.
(c) Fully tighten the bolt (member side).
Torque : 115 Nm (1173 kgf-cm, 85 ft-lbf)
NOTICE:
When installing the bolt, hold the nut in place.
23. INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL
(a) Inspect and adjust the parking brake lever travel Adjustments.
24. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(a) Inspect and adjust the rear wheel alignment Rear Wheel Alignment.
25. CHECK ABS SPEED SENSOR SIGNAL
(a) Check the ABS speed sensor signal Test Mode Procedure.