FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Scion >> 2008 >> xD L4-1.8L (2ZR-FE) >> Repair and Diagnosis >> Engine, Cooling and Exhaust >> Engine >> Seals and Gaskets >> Rear Crankshaft Main Bearing Seal >> Service and Repair >> Removal

Removal








2ZR-FE ENGINE MECHANICAL: REAR CRANKSHAFT OIL SEAL: REMOVAL

REMOVAL

1. DISCHARGE FUEL SYSTEM PRESSURE Vehicle Damage Warnings
2. REMOVE BATTERY Removal

3. REMOVE BATTERY TRAY
4. REMOVE FRONT WHEELS
5. REMOVE ENGINE UNDER COVER LH
6. REMOVE ENGINE UNDER COVER RH
7. DRAIN ENGINE COOLANT Service and Repair

8. DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
9. DRAIN AUTOMATIC TRANSAXLE OIL (for Automatic Transaxle)
10. REMOVE FRONT WIPER ARM HEAD CAP

11. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

12. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

13. REMOVE HOOD TO COWL TOP SEAL

14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

15. REMOVE COWL TOP VENTILATOR LOUVER LH

16. REMOVE FRONT WIPER MOTOR AND LINK

17. REMOVE FRONT AIR SHUTTER SEAL RH Removal

18. REMOVE OUTER COWL TOP PANEL Removal

19. REMOVE AIR CLEANER ASSEMBLY Removal

20. REMOVE AIR CLEANER BRACKET Removal

21. REMOVE BATTERY CARRIER Removal

22. REMOVE NO. 2 CYLINDER HEAD COVER Removal

23. REMOVE FAN AND GENERATOR V BELT Removal

24. REMOVE NO. 2 RADIATOR HOSE Removal

25. REMOVE FRONT BUMPER COVER

26. DISCONNECT NO. 1 RADIATOR HOSE Removal

27. DISCONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transaxle) Removal

28. DISCONNECT NO. 2 OIL COOLER INLET HOSE (for Automatic Transaxle) Removal

29. REMOVE HOOD LOCK ASSEMBLY Removal

30. REMOVE NO. 1 COOLER COVER Removal

31. REMOVE UPPER RADIATOR SUPPORT ABSORBER

32. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY Removal

33. REMOVE RADIATOR ASSEMBLY Removal

34. SEPARATE WITH PULLEY COMPRESSOR ASSEMBLY

35. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle) Removal

36. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle) Removal

37. SEPARATE UNION TO CHECK VALVE HOSE Removal

38. SEPARATE NO. 1 FUEL VAPOR FEED HOSE Removal

39. DISCONNECT ENGINE WIRE Removal

40. DISCONNECT HEATER WATER OUTLET HOSE A(FROM HEATER UNIT) Removal

41. DISCONNECT HEATER WATER INLET HOSE A Removal

42. DISCONNECT FUEL TUBE SUB-ASSEMBLY Removal

43. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle) Removal

44. REMOVE COLUMN HOLE COVER SILENCER SHEET

45. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

46. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

47. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

48. REMOVE CONSOLE PANEL UPPER

49. REMOVE CONSOLE BOX REAR COVER

50. REMOVE CONSOLE BOX CARPET

51. REMOVE REAR CONSOLE BOX ASSEMBLY

52. REMOVE FRONT CONSOLE BOX

53. REMOVE FRONT FLOOR BRACE CENTER Removal

54. REMOVE FRONT EXHAUST PIPE ASSEMBLY Removal

55. REMOVE FRONT AXLE SHAFT LH NUT Removal

56. REMOVE FRONT AXLE SHAFT RH NUT
HINT: The removal procedure for the RH side is the same as that for the LH side.

57. SEPARATE SPEED SENSOR FRONT LH Removal

58. SEPARATE SPEED SENSOR FRONT RH
HINT: The removal procedure for the RH side is the same as that for the LH side.

59. SEPARATE TIE ROD END SUB-ASSEMBLY LH Removal

60. SEPARATE TIE ROD END SUB-ASSEMBLY RH
HINT: The removal procedure for the RH side is the same as that for the LH side.

61. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH Removal

62. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
HINT: The removal procedure for the RH side is the same as that for the LH side.

63. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH Removal

64. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH
HINT: The removal procedure for the RH side is the same as that for the LH side.

65. SEPARATE FRONT AXLE ASSEMBLY LH Removal

66. SEPARATE FRONT AXLE ASSEMBLY RH
HINT: The removal procedure for the RH side is the same as that for the LH side.

67. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH Removal

68. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH Removal

69. REMOVE FLYWHEEL HOUSING UNDER COVER (for Automatic Transaxle) Removal

70. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transaxle) Removal

71. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE Removal

72. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY Removal

73. REMOVE FLYWHEEL HOUSING SIDE COVER

74. REMOVE STARTER ASSEMBLY

75. REMOVE NO. 1 OIL COOLER INLET TUBE (for Automatic Transaxle) Removal

76. REMOVE NO. 1 OIL COOLER OUTLET TUBE (for Automatic Transaxle) Removal

77. REMOVE NO. 2 OIL COOLER TUBE CLAMP (for Automatic Transaxle) Removal

78. REMOVE TRANSMISSION OIL LEVEL GAGE SUB-ASSEMBLY (for Automatic Transaxle)
79. SEPARATE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY (for Automatic Transaxle) Removal

80. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle) Removal

81. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET (for Manual Transaxle) Removal

82. REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle) Removal

83. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle) Removal

84. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)
85. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle) Removal

86. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle) Removal

87. REMOVE ENGINE REAR OIL SEAL






(a) Using a knife, cut off the oil seal lip.
(b) Using a screwdriver with its tip taped, pry out the oil seal.
NOTE: After removing the oil seal, check the crankshaft for damage.
If it is damaged, smooth the surface with 400-grit sandpaper.
pro multis Credits:Operation CHARM About Operation CHARM