P0304

Wiring Diagram:

Cylinder 1,2,3,4,5, Or 6 Misfire Detected (page 1 Of 2):

Cylinder 1,2,3,4,5 Or 6 Misfire Detected (page 2 Of 2):

P0301, P0302, P0303, P0304, P0305, P0306 - CYLINDER (1, 2, 3, 4, 5 OR 6) MISFIRE DETECTED
The crankshaft position (CKP) sensor sends 58 pulses per crankshaft revolution to determine the position and RPM of the engine at various degrees of rotation. The crankshaft reluctor wheel contains 20 notches for every 120° of crankshaft rotation except for two missing notches used to detect cylinder #1 TDC. The ECM bases misfire diagnostics on the principal that at a given speed and load, the time to pass 20 notches on the crankshaft between firing events should be below a certain threshold. If the time to pass 20 notches exceeds a calibrated time, a misfire is detected on the previous cylinder. Under certain conditions. the ECM will monitor misfires in both 200 (catalyst damaging counter) and 1000 (emission related counter) crankshaft revolution tests. If a certain number of misfires (based on engine speed and load) occur over a certain number of engine revolutions which the catalyst may be damaged, the MIL will flash and DTC P0300 will set. If a certain number of misfires (greater than 30 out of a 1000 revolution test, or greater than 45 out of four consecutive 1000 revolution tests) occur over a certain number of engine revolutions, DTC P0300 will set. The MIL will then be commanded On after two consecutive drive cycles if DTC P0300 fails again. The MIL will turn Off after three consecutive passed drive cycles meeting the same criteria or 80 passed drive cycles if the criteria could not be met. DTC P0301-P0306 sets if a specific cylinder misfires for a certain length of time.

DTC PARAMETERS
DTC P0301, P0302. P0303, P0304, P0305 or P0306 will set if specific cylinder misfires have been detected after a 1000 revolution test(s) when;
^ Sum of the misfire counts are greater than 30 in a 1000 engine revolution test or greater than 45 in four consecutive, 1000 engine revolution tests.
^ Engine speed is between 520 and 6520 rpm
^ Six combustion events have occurred
^ Traction control is not active
^ IAT is greater than 8°C (17°F)
^ EVAP diagnostics are not running
^ No CKP or TP sensor DTCs have been set

NOTE: The ECM must complete the entire 1000 revolutions before DTC P0301-P0306 will set.

DTC P0301-P0306 diagnostic runs continuously once the above conditions have been met.

P0301 - P0306 are type B DTCs

DIAGNOSTIC AIDS

IMPORTANT: If a fuel injector DTC is also set, diagnose that DTC first.

IMPORTANT: The ECM will set DTC P0300 even if a specific cylinder is misfiring.

IMPORTANT: If a specific cylinder misfire occurs for longer than 15 seconds, the ECM will command that cylinder fuel injector Off for the rest of the ignition cycle even if the fault is corrected.

If DTCs P0301, P0303, and P0305 are all set with any HO2S bank 1 sensor 1 DTC, this is most likely due to a HO2S bank 1 sensor 1 fault.

If DTCs P0302, P0304, and P0306 are all set with any HO2S bank 2 sensor 1 DTC, this is most likely due to a HO2S bank 2 sensor 1 fault.

The Scan tool contains the SPECIAL FUNCTION. IGNITION COIL CYL. 1-6, which can individually fire the spark plugs. An audible spark plug fire sound can be heard to determine if each cylinder ignition system is functioning correctly.

Use Scan tool to monitor Misfire CURRENT CYL. 1-6) while simulating different engine load conditions in the stall. The Scan tool active misfire counter should pick up intermittent misfire conditions.
^ Fuel injector resistance 16.0+/-0.4 ohms at 21°C (70°F);
OR
All fuel injector resistances are within 1 ohm of each other at the same temperature.
^ Spark plug gap: 0.045 in., not adjustable

NOTE: The misfire history counters will only be erased when DTCs are cleared using Scan tool.