Engine Tightening Specifications

FASTENER TIGHTENING SPECIFICATIONS

A/C Compressor Front Bracket-to-Block 54 Nm (40 lb. ft.)

A/C Compressor Front/Rear Bracket-to-Block/Head 30 Nm (22 lb. ft.)

A/C Compressor-to-Front Bracket 49 Nm (36 lb. ft.)

A/C Compressor-to-Rear Bracket 25 Nm (19 lb. ft.)

Accelerator Bracket Assembly-to-Front of Dash 12 Nm (106 lb. in.)

Accelerator Control Cable Bracket-to-Intake Manifold 30 Nm (22 lb. ft.)

Air Cleaner/Resonator Attachment Bolts (All) 10 Nm (89 lb. in.)

Axle Shaft Intermediate Bracket-to-Block 55 Nm (41 lb. ft.)

Battery Cable-to-Batter 17 Nm (151 lb. in.)

Battery Cable-to-Generator 10 Nm (89 lb. in.)

Battery Case Bracket Stud and Nut 9 Nm (80 lb. in.)

Belt Idler Pulley-to-Front Cover 27 Nm (20 lb. ft.)

Belt Tensioner-to-Block 30 Nm (22 lb. ft.)

Belt Tensioner Pulley 30 Nm (22 lb. ft.)

Block Oil Gallery Plug 30 Nm (22 lb. ft.)

Camshaft Bearing Cap-to-Head (DOHC) 14 Nm (124 lb. in.)

Camshaft Cover-to-Head (DOHC) 10 Nm (89 lb. in.)

Camshaft Sprockets-to-Camshafts 100 Nm (74 lb. ft.)

Camshaft Thrust Bearing-to-Head (SOHC) 25 Nm (19 lb. ft.)

Canister Assembly Band Clamp 3.5 Nm (31 lb. in.)

Canister Purge Solenoid-to-Block 30 Nm (22 lb. ft.)

Catalytic Convertor-to-Isolator 25 Nm (19 lb. ft.)

Clutch Pressure Plate-to-Flywheel 25 Nm (19 lb. ft.)

Connecting Rod Cap-to-Rod
First Pass 25 Nm (19 lb. ft.)

Final Pass 75 degrees

Control Arm to Knuckle - Lower 75 Nm (55 lb. ft.)

Coolant/Cylinder Block Heater 25 Nm (19 lb. ft.)

Coolant Drain-to-Plug/Block 30 Nm (22 lb. ft.)

Cradle-to-Body 205 Nm (151 lb. ft.)

Crankshaft Bearing Cap-to-Block 50 Nm (37 lb. ft.)

Crankshaft Rear Oil Seal Carrier-to-Block 11 Nm (97 lb. in.)

Crankshaft Vibration Damper/Pulley-to-Crankshaft 215 Nm (159 lb. ft.)

Cylinder Head-to-Block Torque Angle

Cylinder Head Core Hole Plug Water Jacket (DOHC) 75 Nm (55 lb. ft.)

Deaeration Line-to-Rocker Cover (SOHC) 10 Nm (89 lb. in.)

Deaeration Line Nut-to-Cylinder Head Fitting (SOHC) 15 Nm (133 lb. in.)

Deaeration Line Clamp-to-Engine Lift Bracket (SOHC) 11 Nm (97 lb. in.)

Deaeration Line Fitting-to-Cylinder Head 8 Nm (71 lb. in.)

Engine Lift Bracket-to-Head (Front and Rear)
No A/C 30 Nm (22 lb. ft.)

Engine Lift Bracket-to-Block - No A/C 47 Nm (35 lb. ft.)

EGR Valve to Head/Intake Manifold - Bolt 25 Nm (19 lb. ft.)

Exhaust Manifold Studs-to-Front Exhaust Pipe 13 Nm (115 lb. in.)

Exhaust Manifold Studs-to-Head 13 Nm (115 lb. in.)

Exhaust Manifold-to-Head (SOHC) 22 Nm (16 lb. ft.)

Exhaust Manifold-to-Head (DOHC) 17 Nm (150 lb. in.)

Exhaust Pipe with Converter-to-Intermediate Pipe 25 Nm (19 lb. ft.)

Exhaust Pipe Clamp-to-Support Bracket 60 Nm (44 lb. ft.)

Exhaust Pipe (Front) to Manifold 31 Nm (23 lb. ft.)

Exhaust Pipe Service Clamps 41 Nm (30 lb. ft.)

Exhaust Pipe Support Bracket-to-Block 45 Nm (33 lb. ft.)

Flexplate-to-Converter 70 Nm (52 lb. ft.)

Flexplate-to-Crankshaft 60 Nm (44 lb. ft.)

Flywheel/Flexplate Cover-to-Case 10 Nm (89 lb. in.)

Flywheel-to-Crankshaft 80 Nm (59 lb. ft.)

Front Cover-to-Block - Lower Center Bolt 10 Nm (89 lb. in.)

Front Cover-to-Head/Block (Perimeter) and
Top Center (DOHC) 30 Nm (22 lb. ft.)

Front Engine Cover Studs (Torque Axis Engine Mount) 10 Nm (89 lb. in.)

Fuel Feed Line Support Clip-to-Bracket 4.5 Nm (37 lb. in.)

Fuel Filter/Pressure Regulator-to-Frame Rail 8 Nm (71 lb. in.)

Fuel Line Shield-to-Underbody 12 Nm (9 lb. ft.)

Fuel Line Support Bracket-to-Block and Intake 30 Nm (22 lb. ft.)

Fuel Rail-to-Intake Manifold 12 Nm (9 lb. ft.)

Fuel Tank Fill Hose-to-Clamp 4 Nm (35 lb. in.)

Fuel Tank Fill Pipe-to-Underbody Rail 8 Nm (71 lb. in.)

Fuel Tank Fill Pipe-to-Upper Bracket 3.5 Nm (31 lb. in.)

Fuel Tank Straps-to-Body 47 Nm (35 lb. ft.)

Fuel/Vapor Lines-to-Body 4 Nm (27 lb. in.)

Generator to Block - Upper/Lower Bolt 32 Nm (24 lb. ft.)

Heater Return Nipple-to-Block 50 Nm (37 lb. ft.)

Heater Outlet-to-Intake Manifold 40 Nm (30 lb. ft.)

Ignition Module-to-Transaxle Case 7 Nm (62 lb. in.)

Intake Manifold-to-Head (SOHC) 30 Nm (22 lb. ft.)

Intake Manifold-to-Head (DOHC) 30 Nm (22 lb. ft.)

Intake Manifold Stud-to-Head (P/S Bracket, DOHC) 30 Nm (22 lb. ft.)

Intake Manifold Studs-to-Head 13 Nm (115 lb. in.)

Intake Manifold Support Bracket-to-Block (LH) 30 Nm (22 lb. ft.)

Intake Manifold Support Bracket-to-Block (RH) 55 Nm (41 lb. ft.)

Intake Manifold Support Bracket-to-Manifold (DOHC) 30 Nm (22 lb. ft.)

Motor Mount - Front-to-Block 70 Nm (52 lb. ft.)

Motor Mount - Front-to-Front
Cover (Torque Axis Engine Mount) 50 Nm (37 lb. ft.)

Motor Mount - Rear-to-Block (LH and RH) 48 Nm (35 lb. ft.)

Muffler Isolator Block-to-Body 25 Nm (19 lb. ft.)

Muffler Strap around Muffler 22 Nm (16 lb. ft.)

Oil Baffle Plate-to-Block (DOHC) 55 Nm (41 lb. ft.)

Oil Filter-to-Block Gasket Contact and 3/4 to 1 Turn

Oil Filter Fitting-to-Block 30 Nm (22 lb. ft.)

Oil Gallery Plug-to-Block 30 Nm (22 lb. ft.)

Oil Level Indicator Tube-to-Block 30 Nm (22 lb. ft.)

Oil Pan-to-Block 9 Nm (80 lb. in.)

Oil Pan Drain Plug-to-Pan 37 Nm (27 lb. ft.)

Oil Pickup Tube-to-Block 15 Nm (133 lb. in.)

Oil Pipe Bracket-to-Block (SOHC) 55 Nm (41 lb. ft.)

Oil Pipe Bracket-to-Block/Baffle Plate (DOHC) 15 Nm (133 lb. in.)

Oil Pump Cover-to-Front Cover 11 Nm (97 lb. in.)

Power Steering
Hoses-to-Gear and Pump 27 Nm (20 lb. ft.)

Power Steering
Pump Bracket-to-Block 30 Nm (22 lb. ft.)

Power Steering
Pump-to-Bracket 30 Nm (22 lb. ft.)

Power Steering Pump
Lower Support Bracket-to-Intake Manifold (DOHC) 30 Nm (22 lb. ft.)

Power Steering Pump
Lower Support Bracket-to-Pump Bracket (DOHC) 30 Nm (22 lb. ft.)

Power Steering Pump
Upper Support Bracket-to-Pump/Intake Manifold (DOHC) 30 Nm (22 lb. ft.)

Power Steering Return Hose Clamp-to-Pump 2 Nm (18 lb. in.)

Radiator Support Brackets 10 Nm (89 lb. in.)

Rocker Arm Cover-to-Head (SOHC) 30 Nm (22 lb. ft.)

Rocker Arm Shaft-to-Head 25 Nm (19 lb. ft.)

Sensor - Coolant Temperature-to-Head (PCM) 8 Nm (71 lb. in.)

Sensor - Crankshaft Position-to-Block 9 Nm (80 lb. in.)

Sensor - ESC Knock-to-Block 15 Nm (133 lb. in.)

Sensor - Idle Air Control 3.2 Nm (28 lb. in.)

Sensor - Induction Air-to-Intake Tube 5 Nm (44 lb. in.)

Sensor - Map-to-Intake Manifold 3 Nm (27 lb. in.)

Sensor - Oil Pressure-to-Block 45 Nm (33 lb. ft.)

Sensor - Oxygen-to-Exhaust Manifold 45 Nm (33 lb. ft.)

Sensor - Throttle Position (TP) Switch 2 Nm (18 lb. in.)

Sensor - Vehicle Speed 26 Nm (19 lb. in.)

Spark Plug-to-Head 27 Nm (20 lb. ft.)

Starter Motor-to-Block 37 Nm (27 lb. ft.)

Steering Joint-to-Gear 47 Nm (35 lb. ft.)

Stiffening Bracket-to-Engine/Transaxle
Case/Exhaust Down Pipe 54 Nm (40 lb. ft.)

Strut-to-Knuckle 200 Nm (148 lb. ft.)

Thermostat Housing-to-Block 30 Nm (22 lb. ft.)

Throttle Body-to-Air Intake Manifold 31 Nm (23 lb. ft.)

Timing Chain Fixed Guide-to-Block 26 Nm (19 lb. ft.)

Timing Chain Fixed Guide-to-Head 26 Nm (19 lb. ft.)

Timing Chain Pivot Guide-to-Head 26 Nm (19 lb. ft.)

Timing Chain Tensioner-to-Block 19 Nm (168 lb. in.)

Torque Converter-to-Flexplate 70 Nm (52 lb. ft.)

Torque Strut-to-Cradle Bracket and
Engine Front Mount-RH (Torque Axis Engine Mount) 50 Nm (37 lb. ft.)

Transaxle Case to Block - Lower Bolts 130 Nm (98 lb. ft.)

Transaxle Case to Block - Upper Studs 90 Nm (66 lb. ft.)

Transaxle Flywheel/Flexplate
Dust Cover to Transaxle 10 Nm (89 lb. in.)

Transaxle Lower Mount-to-Cradle 50 Nm (37 lb. ft.)

Transaxle Lower Mount-to-Transaxle 31 Nm (23 lb. ft.)

Transaxle to Rear Mount-to-Transaxle 30 Nm (22 lb. ft.)

Transaxle Torque Strut to Midrail 50 Nm (37 lb. ft.)

Underbody Frame Rail Support (Fuel Line) 12 Nm (106 lb. in.)

Upper Engine Mount-to-Front Cover and
RH Frame Rail Bracket (Torque Axis Engine Mount) 50 Nm (37 lb. ft.)

Water Pump-to-Block 30 Nm (22 lb. ft.)

Water Pump Pulley-to-Water Pump Hub 25 Nm (19 lb. ft.)

Wiring Harness Clamps-to-Block 25 Nm (19 lb. ft.)

Wiring Harness PCM Ground-to-Block 10 Nm (89 lb. in.)

Wiring Harness-to-Generator (Positive Terminal) 10 Nm (89 lb. in.)

Wiring Harness-to-Starter (Positive Terminal) 10 Nm (89 lb. in.)

Wiring Harness-to-Starter (Solenoid Terminal) 4 Nm (35 lb. in.)

Wiring Harness-to-Transaxle Case/Engine Block (2) 25 Nm (18 lb. ft.)