Anti-Theft Alarm Fitting Kit

Kit components (4D)







1 Bonnet switch
2 Protective cover for bonnet switch
3 Blind rivet
4 Siren
5 Nut
6 Lens cover with glass breakage sensor (textile or leather trim)
7 Tilt sensor
8 Plastic nut (qty 2)
9 Labels

Labels, decals
The labels and decals should be attached to the front side windows and the windscreen.

Kit components (5D)







1 Bonnet switch
2 Protective cover for bonnet switch
3 Blind rivet
4 Siren
5 Nut
6 Front lens cover with glass breakage sensor (textile or leather trim)
7 Rear lens cover with glass breakage sensor
8 Tilt sensor
9 Plastic nut (qty 2)
10 Labels

Labels, decals
The labels and decals should be attached to the front side windows and the windscreen.

Bonnet switch







1 Open the bonnet and lift up the main fuse box to find the wiring harness with the connector to the bonnet switch.
2 Plus the connector on to the switch.
3 Fit the switch in its holder.

Protective cover for bonnet switch (EU,GB)







1 Open the bonnet. On the inside of the bonnet there is a predrilled hole exactly above the bonnet switch.
2 Fit the cover into the hole using a rivet.

Siren







1 Raise the car and remove the left front wheel.
2 Remove the front part of the wing liner from the left-hand front wheel housing. Localize the wiring harness and a 3 pin connector.
3 Fit the siren on to the prewelded screw and tighten it down with a nut and a screw.







4 Plug in the connector on the siren.
5 Fit the wing liner and left-hand front wheel in position again and lower the car to the ground.

Glass breakage sensor (4D)







1 Remove the existing lens cover from the central roof lamp.
2 Remove the switch panel from the roof lamp in order to gain access to the connector for the glass breakage sensor. Pull out the connector and fit the switch panel back into position again.
3 Connect the glass breakage sensor on the new lens cover to the connector.
4 Press the lens cover into position.
5 Finally, the glass breakage sensor must be programmed for the anti-theft alarm with the diagnostic instrument. If an angle sensor is also to be fitted, perform programming after the angle sensor has been fitted. See Programming, Anti-theft Protection

Glass breakage sensor, front (5D)







1 Remove the existing lens cover from the central roof lamp.
2 Detach the switch panel from the roof lamp to gain access to the connectors for the glass breakage sensor. Pull out the connectors and refit the switch panel.
3 Connect the glass breakage sensor on the new lens cover to the connectors.
4 Press the lens cover into position.
5 Finally, the glass breakage sensor must be programmed for the anti-theft alarm with the diagnostic instrument. If an angle sensor is also to be fitted, perform programming after the angle sensor has been fitted. See Programming, Anti-theft Protection.

Glass breakage sensor, rear (5D)







1 Remove the cover with roof lamp in the luggage compartment.
2 Remove the lamp glass from the cover.







3 Undo the plastic cup.
4 Pull out the cable and connector for the glass breakage sensor.
5 Fit the plastic cup
6 Connect the glass breakage sensor and the lamp and fit the cover.
7 Fit the glass breakage sensor into the cover.
8 Finally, the glass breakage sensor must be programmed for the anti-theft alarm with the diagnostic instrument. If an angle sensor is also to be fitted, perform programming after the angle sensor has been fitted. See Programming, Anti-theft Protection.

Tilt sensor







1 Push the right-hand front seat forwards and adjust the back of the seat to a vertical position.
2 Fold the floor mat under the seat to reveal the attachment points (2 prewelded screws) and electrical connector for the tilt sensor.
3 Fit the tilt sensor on the screws and tighten the plastic nuts.
4 Plug the connector on to the sensor. Fold the mat back again and reposition the seat.
5 Finally, the angle sensor must be programmed for the anti-theft alarm using the diagnostic instrument. See Programming, Anti-theft Protection.